Datamax PE manual Agency Compliance and Approvals

Page 5

Agency Compliance and Approvals

UL: UL1950 Safety of Information Technology Equipment

1. Nur für Gebrauch innerhalb eines Gebäudes geeignet.

Für 230 Volt (Europa): Benützen Sie ein Kabel, das mit "HAR" markiert ist, bestehend mindestens aus einem H05VV-F Kabel, das mindestens 0,75 Quadratmillimeter Drahtdurchmesser hat; sowie eine IEC320 Steckdose und einen für das Land geeigneten Stecker, 6A, 250 Volt.

1.This unit is intended for indoor use only.

2.Disconnect power supply cord in case of emergency.

3.When power supply cord is not provided; for proper power supply cord selection please see below:

CE: This product complies with requirements of the Low Voltage Directive 73/23/EEC and the provisions of the EMC Directive 89/336/EEC.

For 230 Volt Operation (Europe): Use a cord set, marked "HAR," consisting of a min H05VV-F cord which has a minimum 0.75 square

mmdiameter conductors, provided with an IEC 320 receptacle and a male plug for the country of installation rated 6A, 250V

For 120 Volt Operation (Domestic):

FCC: This device complies with FCC CFR 47 Part 15 Class A.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions in this manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Image 5

Contents PE Series Operator’s Manual Page 88-2082-01 Rev. C1 Page Agency Compliance and Approvals Important Safety Instructions Contents Using Your Printer Appendix B Appendix aAppendix C Appendix DPage Right-Hand Model Printer OverviewIntroduction About This Printer Standard FeaturesOptional Features PE Series Operator’s Manual Getting Started Before Using This PrinterInspecting the Printer Right-Hand Model, External Front View General OverviewRight-hand Model, Interior Front View Connecting the Printer Setting Up the PrinterHead-Lift Lever Loading MediaMedia Loading Media Loading detail Ribbon Loading Path Loading Ribbon Thermal TransferJ-Hook Removal of a Partially Used Roll of Ribbon Ribbon RemovalRemoval of a Completely Used Ribbon Flash Cartridge Connector Location Installing a Flash Cartridge10 Inserting the Memory Cartridge Printing a Configuration Label 11 Configuration Label PE Series Operator’s Manual Configuration Label Explanation 12 Test Pattern Label Test Pattern LabelApplicator Port Pin Assignments Pin function explanation Applicator ConnectionPin 4 Not Used Pin # Function Direction13 End Print Signal Options Options Port Pin Assignments Options PortDescription PE Series Operator’s Manual Control Buttons Using Your PrinterUsing the Printer’s Front Panel LCD Contrast LightsMenu Keypad Basic Functions Accessing the Menu TreeFactory preset Value range PE Output Signal Advanced SetupRibbon Low Heat SettingBackfeed Cntrl Slew Speed Print SpeedBackfeed Speed Label WidthModify Password Factory SettingsSymbol Set Security CheckPause Mode ProdigyPlus ModeFeedback Mode Offset Bias *220Comm Setup *PORTA *9600 *8 *N *1 *BOTH Control Codes Test ModeFront Panel Test PrintTest I/O Serial LoopbackPrint Directory Installed OptionsPrint File Copy ModuleInputs Sensor Name Possible Condition Sensor DefinitionsPE Series Operator’s Manual Media Sensor Adjustment Example of the Media Width Adjustment Media Width AdjustmentLabel Presentation Label Start of PrintSetting Start of Print and Peel Position Controlling Print Quality PE Series Operator’s Manual Exterior InteriorArea Method Interval Cleaning SchedulePrinter Cleaning Schedule Cleaning the Printhead Cleaning the PrintheadCleaning the Platen Roller Printer fails to power up no lights Troubleshooting TipsSkips Labels every other Black boxes in displayPoor Print Quality No PrintMissing Data in the printed label LCD Display Error MessagesAlarm Description BQQMJDBUPS!CVTZ DPWFS!PQFO!GBVM U IFBE!VQ!GBVMU PVU!PG!TUPDL QSJOUIFBE!GMU SJCCPO!GBVMU SJC!TBWFS!GBVMU UPG!GBVMU Ascii Character Dump Label Character Dump ModePage Appendix a Ascii Control ChartPE Series Operator’s Manual Available Fonts and Barcodes Appendix BTable B-1 Human-Readable Font Sizes Human-Readable FontsTable B-2 Valid Human-Readable Font Ascii Characters Font Matrix Sizes Charac. Per Inch Dot 203 Height WidthPage Identifies the internal Triumvirate font Table B-3 Valid Bar Code Font Ascii Characters Barcode FontsPE Series Operator’s Manual Barcode O Barcode S Barcode T Barcode z Table C-1 Serial Cable Requirements Appendix CCable Listing PE Series Operator’s Manual Applicator Port Test Box Appendix DPE Series Operator’s Manual Appendix E Error CodesPE Series Operator’s Manual Appendix F Printer SpecificationsPrinting CommunicationsEnvironmental ElectricalPhysical MediaFonts and Bar Codes Figure F-1 Print Engine Critical Dimensions Printer DimensionsTable F-1 Acceptable Media Specifications Media SpecificationsLabel Type Print Image Ribbon Type Speed Energy Durability Media and Ribbon BasicsTable F-2 Media and Ribbon Overview Menu Tree Appendix GPE Series Operator’s Manual Appendix H Warranty InformationPrinter Thermal printheadGeneral Warranty Provisions Warranty Service ProceduresLimitation of Liability PE Series Operator’s Manual