Code Alarm CR3 manual Reader Battery Installation, Attaching and Detaching the Lithium Ion Battery

Page 29

1.13 - Reader Battery Installation

Attaching and Detaching the Lithium Ion Battery

The CR3 can be purchased with a 1950 mAH Lithium Ion battery. To install battery, make sure the battery is in the correct position (ﬁ gure 1.21). Place the plastic tab of the battery into the reader (ﬁ gure 1.22). Push the battery in and slide the locking mechanism down (ﬁ gures 1.23 & 1.24)

Charging the Lithium Ion Battery

The battery automatically charges everytime a cable inteface is attached to the unit and the host is powered up.

Note: The RS232 interface power adapter must be plugged into a wall socket for the unit to charge.

If you power-up the CR3 with a completely discharged battery it will take up to 10 minutes before the unit will become operational.

Figure 1.21

Figure 1.22

Figure 1.23

Figure 1.24

Save Settings

C002332_09_CR3 User Manual - 23

Image 29

Contents Manual Version Laser/LED Radiation Statement of Agency ComplianceSave Settings Table of Contents Reader Feedback and Special Settings CR3 Programming Symbology SettingsAdvanced Decode Performance Adding a Preﬁx or Sufﬁx and Reader Text CommandsCR3 Maintenance and Troubleshooting Getting Started Introduction Unpacking Powering On/Off ReaderDescription of Button Function Keypad/Icon OverviewIcon Description Power IconsIntroduction RS232 Considerations RS232 Batch Cable-Detect DefaultBatch Operation Introduction Cabled OperationUSB Keyboard Mode USB Cable Installation GuideUSB Virtual COM 1 Way Mode USB Communication SettingsReset to USB Factory Defaults USB Keyboard USB DownloaderPS2 Mode Save Settings PS2 Cable Installation GuidePS2 Communication Settings Mode RS232 One Way Mode RS232 Cable Installation GuideBaud Rate Stop Bits Data Bits Parity NoneRS232 Communication Stop Bit Settings RS232 Communication Data Bit SettingsRS232 Communication Baud Rate Settings RS232 Communication Parity SettingsCabled 2 hours Cabled Always Default Cabled Reader Time Out SettingsExample Reset to RF Factory Defaults QuickConnect Bluetooth Radio OperationRF Two Way Mode RF One Way Mode Max RangeBluetooth Radio Auto Connect On Default Bluetooth Radio Auto ConnectBluetooth Disconnect Bluetooth Radio Out of Range Notiﬁcation Settings Bluetooth Radio Auto DisconnectBluetooth Radio Time Out Settings Uncabled Operations RS232 Bluetooth RadioReader Feedback Guide Targeting and Reading Techniques To read a symbol with the CR3Imager Field of View and Resolution Decode Zone H1 Handle BH1 or BH2 Battery HandleAttaching Handles Attaching and Detaching the Lithium Ion Battery Reader Battery InstallationOptimization and Trigger Programming DOT IntroductionGlobal Trigger Optimization Matrix Left Trigger Optimization Matrix Read Codes with Both Imagers DefaultLeft Trigger Programming Read with Near-Field Imager onlyRead Code with Near-Field Imager only Right Trigger Optimization MatrixRight Trigger Programming Handle Trigger Programming Handle Optimization MatrixContinuous Trigger Optimization Far Field Only On Off DefaultContinuous Scan Both Near & Far Field OnMotion Detection Scan Settings Continuous Scan SettingsContinuous Scan Trigger Delays Continuous Scan Sleep Time OutCR3 Programming Symbology Settings Codabar Symbology Aztec SymbologyCode 11 Symbology Codablock F SymbologyCode 39 Symbology Codablock F On Codablock F Off DefaultCode 128 Symbology Code 93 SymbologyCode 93 On Default Code 93 Off Sample Trioptic CodeGoCode Symbology Composite SymbologiesData Matrix Symbology Maxicode Symbology Interleaved 2 of 5 SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy Matrix 2 of 5 SymbologyMSI Plessy Symbology NEC 2 of 5 On NEC 2 of 5 Off Default NEC 2 of 5 SymbologyRoyal Mail On Disable All Postal Codes Default Postal SymbologiesPharmacode Australian Post On Japan Post OnRSS Symbology QR Code SymbologyUPC/EAN/JAN Telepen SymbologyReader Feedback and Special Settings Off Default Low Medium Volume and Vibration SettingsCode Readability Index Vibrate On / Beep On Vibrate On / Beep OffLow Med Default High Backlight Intensity SettingsReadability Index Output Disable Reader Power Off Settings Backlight Timeout SettingsLaser Settings Reader Settings Locked Reader Settings LockReader ID and Firmware Version Reader ID and FirmwareUS English Default US English Leading Time Stamp SettingsKeyboard Support No Leading French GermanReader ID Firmware Version Lockout Link Mode Lock-out Link ModeAdvanced Decode Performance Enable Continuous Illumination DefaultContinuous Illumination Set Targeting Zone TolerancesWindowing Large 2-Dimensional Codes 640 x 640 pixels Codes Enable Sxga 1280 x VGA & Megapixel SettingsEnable VGA 640 x Mirror DecodingAdding a Preﬁx or Sufﬁx and Reader Text Commands Preﬁx Comma Preﬁx Space Preﬁx SettingsSufﬁx Settings Reader Text Commands Erase Preﬁx and Sufﬁx SettingsReader Text Commands On Erase Preﬁx & Sufﬁx DataCR3 Maintenance and Troubleshooting General Safety Information Reset Reader to Factory DefaultsLimited Warranty WarrantyTerms of Warranty Warranty Coverage and ProcedureGeneral CR3 AccessoriesCR3 Maintenance Frequently Asked QuestionsCleaning the CR3 Window Technical Support and Returns