Code Alarm CR3 Advanced Decode Performance, Adding a Preﬁx or Sufﬁx and Reader Text Commands

Page 6

4.11 - Lockout Link Mode		49
Chapter 5 - Advanced Decode Performance		50
5.1	- Continuous Illumination	51
5.2	- Set Targeting Zone Tolerances	51
5.3	- Windowing	52
5.4	- VGA & Megapixel Settings	54
5.5	- Mirror Decoding	54
Chapter 6 - Adding a Preﬁx or Sufﬁx and Reader Text Commands		55
6.1	- Preﬁ x Settings	56
6.2	- Sufﬁ x Settings	56
6.3	- Reader Text Commands	57
6.4	- Erase Preﬁ x and Sufﬁ x Settings	57
Chapter 7 - CR3: Maintenance and Troubleshooting		58
7.1	- Reset Reader to Factory Defaults	59
7.2	- General Safety Information	59
7.3	- Warranty	60
7.4	- CR3 Accessories	61
7.5	- Frequently Asked Questions	62
7.6	- CR3 Maintenance	62

Save Settings	C002332_09_CR3 User Manual - v

Image 6

Contents Manual Version Statement of Agency Compliance Laser/LED RadiationSave Settings Table of Contents CR3 Programming Symbology Settings Reader Feedback and Special SettingsAdding a Preﬁx or Sufﬁx and Reader Text Commands CR3 Maintenance and TroubleshootingAdvanced Decode Performance Getting Started Introduction Powering On/Off Reader UnpackingKeypad/Icon Overview Description of Button FunctionPower Icons Icon DescriptionRS232 Batch Cable-Detect Default Batch OperationIntroduction RS232 Considerations Cabled Operation IntroductionUSB Cable Installation Guide USB Keyboard ModeReset to USB Factory Defaults USB Communication SettingsUSB Virtual COM 1 Way Mode USB Keyboard USB DownloaderPS2 Cable Installation Guide PS2 Communication SettingsPS2 Mode Save Settings Baud Rate RS232 Cable Installation GuideMode RS232 One Way Mode Stop Bits Data Bits Parity NoneRS232 Communication Baud Rate Settings RS232 Communication Data Bit SettingsRS232 Communication Stop Bit Settings RS232 Communication Parity SettingsCabled Reader Time Out Settings Cabled 2 hours Cabled Always DefaultBluetooth Radio Operation Example Reset to RF Factory Defaults QuickConnectRF One Way Mode Max Range RF Two Way ModeBluetooth Radio Auto Connect Bluetooth DisconnectBluetooth Radio Auto Connect On Default Bluetooth Radio Auto Disconnect Bluetooth Radio Time Out Settings Uncabled OperationsBluetooth Radio Out of Range Notiﬁcation Settings Bluetooth Radio Reader Feedback GuideRS232 To read a symbol with the CR3 Targeting and Reading TechniquesImager Field of View and Resolution Decode Zone BH1 or BH2 Battery Handle Attaching HandlesH1 Handle Reader Battery Installation Attaching and Detaching the Lithium Ion BatteryOptimization and Trigger Programming Introduction DOTGlobal Trigger Optimization Matrix Left Trigger Programming Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Read with Near-Field Imager onlyRight Trigger Optimization Matrix Right Trigger ProgrammingRead Code with Near-Field Imager only Handle Optimization Matrix Handle Trigger ProgrammingContinuous Scan Far Field Only On Off DefaultContinuous Trigger Optimization Both Near & Far Field OnContinuous Scan Trigger Delays Continuous Scan SettingsMotion Detection Scan Settings Continuous Scan Sleep Time OutCR3 Programming Symbology Settings Aztec Symbology Codabar SymbologyCode 39 Symbology Codablock F SymbologyCode 11 Symbology Codablock F On Codablock F Off DefaultCode 93 On Default Code 93 Off Code 93 SymbologyCode 128 Symbology Sample Trioptic CodeComposite Symbologies Data Matrix SymbologyGoCode Symbology Interleaved 2 of 5 Symbology Maxicode SymbologyMatrix 2 of 5 Symbology MSI Plessy SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 Symbology NEC 2 of 5 On NEC 2 of 5 Off DefaultPharmacode Postal SymbologiesRoyal Mail On Disable All Postal Codes Default Australian Post On Japan Post OnQR Code Symbology RSS SymbologyTelepen Symbology UPC/EAN/JANReader Feedback and Special Settings Code Readability Index Volume and Vibration SettingsOff Default Low Medium Vibrate On / Beep On Vibrate On / Beep OffBacklight Intensity Settings Readability Index Output DisableLow Med Default High Backlight Timeout Settings Laser SettingsReader Power Off Settings Reader ID and Firmware Version Reader Settings LockReader Settings Locked Reader ID and FirmwareKeyboard Support Time Stamp SettingsUS English Default US English Leading No Leading French GermanLock-out Link Mode Reader ID Firmware Version Lockout Link ModeAdvanced Decode Performance Continuous Illumination DefaultEnable Continuous Illumination Set Targeting Zone TolerancesWindowing Large 2-Dimensional Codes 640 x 640 pixels Enable VGA 640 x VGA & Megapixel SettingsCodes Enable Sxga 1280 x Mirror DecodingAdding a Preﬁx or Sufﬁx and Reader Text Commands Preﬁx Settings Sufﬁx SettingsPreﬁx Comma Preﬁx Space Reader Text Commands On Erase Preﬁx and Sufﬁx SettingsReader Text Commands Erase Preﬁx & Sufﬁx DataCR3 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety InformationTerms of Warranty WarrantyLimited Warranty Warranty Coverage and ProcedureCR3 Accessories GeneralCleaning the CR3 Window Frequently Asked QuestionsCR3 Maintenance Technical Support and Returns

Chapter 5 - Advanced Decode Performance

Chapter 6 - Adding a Preﬁx or Sufﬁx and Reader Text Commands

Chapter 7 - CR3: Maintenance and Troubleshooting

Save Settings