Code Alarm CR3 Erase Prefix and Suffix Settings, Reader Text Commands, Erase Prefix & Suffix Data

Page 63

Suffix - Tab

Suffix - Tab

Suffix - Erase / None

Only Use with USB

Only Use with

This code will

Keyboard, PS2

Serial

erase all suffi x

Keyboard Mode or

Application

data.

with CodeXML Router

 

 

or PS2 CodeXML

 

 

Bluetooth Modem

 

 

6.3 - Erase Prefix and Suffix Settings

Scan the following codes to erase all prefi x and suffi x data.

Erase Prefix & Suffix Data

6.4 - Reader Text Commands

Enabling Reader Text Commands allows the CR3 to accept text commands via RS232 or RF commmunication. Scan the following codes to enable/disable reader text commands:

Reader Text Commands On

Reader Text Commands Off - Default

Note: Text commands can only be sent to the reader when it is active.

Save Settings

C002332_09_CR3 User Manual - 57

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Manual Version Laser/LED Radiation Statement of Agency ComplianceSave Settings Table of Contents Reader Feedback and Special Settings CR3 Programming Symbology SettingsAdding a Prefix or Suffix and Reader Text Commands CR3 Maintenance and TroubleshootingAdvanced Decode Performance Getting Started Introduction Unpacking Powering On/Off ReaderDescription of Button Function Keypad/Icon OverviewIcon Description Power IconsRS232 Batch Cable-Detect Default Batch OperationIntroduction RS232 Considerations Introduction Cabled OperationUSB Keyboard Mode USB Cable Installation GuideUSB Keyboard USB Downloader USB Communication SettingsUSB Virtual COM 1 Way Mode Reset to USB Factory DefaultsPS2 Cable Installation Guide PS2 Communication SettingsPS2 Mode Save Settings Stop Bits Data Bits Parity None RS232 Cable Installation GuideMode RS232 One Way Mode Baud RateRS232 Communication Parity Settings RS232 Communication Data Bit SettingsRS232 Communication Stop Bit Settings RS232 Communication Baud Rate SettingsCabled 2 hours Cabled Always Default Cabled Reader Time Out SettingsExample Reset to RF Factory Defaults QuickConnect Bluetooth Radio OperationRF Two Way Mode RF One Way Mode Max RangeBluetooth Radio Auto Connect Bluetooth DisconnectBluetooth Radio Auto Connect On Default Bluetooth Radio Auto Disconnect Bluetooth Radio Time Out Settings Uncabled OperationsBluetooth Radio Out of Range Notification Settings Bluetooth Radio Reader Feedback GuideRS232 Targeting and Reading Techniques To read a symbol with the CR3Imager Field of View and Resolution Decode Zone BH1 or BH2 Battery Handle Attaching HandlesH1 Handle Attaching and Detaching the Lithium Ion Battery Reader Battery InstallationOptimization and Trigger Programming DOT IntroductionGlobal Trigger Optimization Matrix Read with Near-Field Imager only Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Left Trigger ProgrammingRight Trigger Optimization Matrix Right Trigger ProgrammingRead Code with Near-Field Imager only Handle Trigger Programming Handle Optimization MatrixBoth Near & Far Field On Far Field Only On Off DefaultContinuous Trigger Optimization Continuous ScanContinuous Scan Sleep Time Out Continuous Scan SettingsMotion Detection Scan Settings Continuous Scan Trigger DelaysCR3 Programming Symbology Settings Codabar Symbology Aztec SymbologyCodablock F On Codablock F Off Default Codablock F SymbologyCode 11 Symbology Code 39 SymbologySample Trioptic Code Code 93 SymbologyCode 128 Symbology Code 93 On Default Code 93 OffComposite Symbologies Data Matrix SymbologyGoCode Symbology Maxicode Symbology Interleaved 2 of 5 SymbologyMatrix 2 of 5 Symbology MSI Plessy SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 On NEC 2 of 5 Off Default NEC 2 of 5 SymbologyAustralian Post On Japan Post On Postal SymbologiesRoyal Mail On Disable All Postal Codes Default PharmacodeRSS Symbology QR Code SymbologyUPC/EAN/JAN Telepen SymbologyReader Feedback and Special Settings Vibrate On / Beep On Vibrate On / Beep Off Volume and Vibration SettingsOff Default Low Medium Code Readability IndexBacklight Intensity Settings Readability Index Output DisableLow Med Default High Backlight Timeout Settings Laser SettingsReader Power Off Settings Reader ID and Firmware Reader Settings LockReader Settings Locked Reader ID and Firmware VersionNo Leading French German Time Stamp SettingsUS English Default US English Leading Keyboard SupportReader ID Firmware Version Lockout Link Mode Lock-out Link ModeAdvanced Decode Performance Set Targeting Zone Tolerances DefaultEnable Continuous Illumination Continuous IlluminationWindowing Large 2-Dimensional Codes 640 x 640 pixels Mirror Decoding VGA & Megapixel SettingsCodes Enable Sxga 1280 x Enable VGA 640 xAdding a Prefix or Suffix and Reader Text Commands Prefix Settings Suffix SettingsPrefix Comma Prefix Space Erase Prefix & Suffix Data Erase Prefix and Suffix SettingsReader Text Commands Reader Text Commands OnCR3 Maintenance and Troubleshooting General Safety Information Reset Reader to Factory DefaultsWarranty Coverage and Procedure WarrantyLimited Warranty Terms of WarrantyGeneral CR3 AccessoriesTechnical Support and Returns Frequently Asked QuestionsCR3 Maintenance Cleaning the CR3 Window
Top Page Image Contents