Code Alarm CR3 manual Interleaved 2 of 5 Symbology, Maxicode Symbology

Page 43

3.12 - Interleaved 2 of 5 Symbology

Scan the following codes to enable/disable Interleaved 2 of 5 symbology settings:

Int 2 of 5 On (Default)

Int 2 of 5 Off

Int 2 of 5 Two Digits On

Int 2 of 5 Two Digits Off

Int 2 of 5 Four Digits On

Int 2 of 5 Four Digits Off

Sample Int 2 of 5 Code

 

 

3.13 - Maxicode Symbology

Scan the following codes to enable/disable Maxicode symbology settings:

Maxicode On

Maxicode Off (Default)

Sample Maxicode

Save Settings

C002332_09_CR3 User Manual - 37

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Manual Version Laser/LED Radiation Statement of Agency ComplianceSave Settings Table of Contents Reader Feedback and Special Settings CR3 Programming Symbology SettingsCR3 Maintenance and Troubleshooting Adding a Prefix or Suffix and Reader Text CommandsAdvanced Decode Performance Getting Started Introduction Unpacking Powering On/Off ReaderDescription of Button Function Keypad/Icon OverviewIcon Description Power IconsBatch Operation RS232 Batch Cable-Detect DefaultIntroduction RS232 Considerations Introduction Cabled OperationUSB Keyboard Mode USB Cable Installation GuideUSB Keyboard USB Downloader USB Communication SettingsUSB Virtual COM 1 Way Mode Reset to USB Factory DefaultsPS2 Communication Settings PS2 Cable Installation GuidePS2 Mode Save Settings Stop Bits Data Bits Parity None RS232 Cable Installation GuideMode RS232 One Way Mode Baud RateRS232 Communication Parity Settings RS232 Communication Data Bit SettingsRS232 Communication Stop Bit Settings RS232 Communication Baud Rate SettingsCabled 2 hours Cabled Always Default Cabled Reader Time Out SettingsExample Reset to RF Factory Defaults QuickConnect Bluetooth Radio OperationRF Two Way Mode RF One Way Mode Max RangeBluetooth Disconnect Bluetooth Radio Auto ConnectBluetooth Radio Auto Connect On Default Bluetooth Radio Time Out Settings Uncabled Operations Bluetooth Radio Auto DisconnectBluetooth Radio Out of Range Notification Settings Reader Feedback Guide Bluetooth RadioRS232 Targeting and Reading Techniques To read a symbol with the CR3Imager Field of View and Resolution Decode Zone Attaching Handles BH1 or BH2 Battery HandleH1 Handle Attaching and Detaching the Lithium Ion Battery Reader Battery InstallationOptimization and Trigger Programming DOT IntroductionGlobal Trigger Optimization Matrix Read with Near-Field Imager only Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Left Trigger ProgrammingRight Trigger Programming Right Trigger Optimization MatrixRead Code with Near-Field Imager only Handle Trigger Programming Handle Optimization MatrixBoth Near & Far Field On Far Field Only On Off DefaultContinuous Trigger Optimization Continuous ScanContinuous Scan Sleep Time Out Continuous Scan SettingsMotion Detection Scan Settings Continuous Scan Trigger DelaysCR3 Programming Symbology Settings Codabar Symbology Aztec SymbologyCodablock F On Codablock F Off Default Codablock F SymbologyCode 11 Symbology Code 39 SymbologySample Trioptic Code Code 93 SymbologyCode 128 Symbology Code 93 On Default Code 93 OffData Matrix Symbology Composite SymbologiesGoCode Symbology Maxicode Symbology Interleaved 2 of 5 SymbologyMSI Plessy Symbology Matrix 2 of 5 SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 On NEC 2 of 5 Off Default NEC 2 of 5 SymbologyAustralian Post On Japan Post On Postal SymbologiesRoyal Mail On Disable All Postal Codes Default PharmacodeRSS Symbology QR Code SymbologyUPC/EAN/JAN Telepen SymbologyReader Feedback and Special Settings Vibrate On / Beep On Vibrate On / Beep Off Volume and Vibration SettingsOff Default Low Medium Code Readability IndexReadability Index Output Disable Backlight Intensity SettingsLow Med Default High Laser Settings Backlight Timeout SettingsReader Power Off Settings Reader ID and Firmware Reader Settings LockReader Settings Locked Reader ID and Firmware VersionNo Leading French German Time Stamp SettingsUS English Default US English Leading Keyboard SupportReader ID Firmware Version Lockout Link Mode Lock-out Link ModeAdvanced Decode Performance Set Targeting Zone Tolerances DefaultEnable Continuous Illumination Continuous IlluminationWindowing Large 2-Dimensional Codes 640 x 640 pixels Mirror Decoding VGA & Megapixel SettingsCodes Enable Sxga 1280 x Enable VGA 640 xAdding a Prefix or Suffix and Reader Text Commands Suffix Settings Prefix SettingsPrefix Comma Prefix Space Erase Prefix & Suffix Data Erase Prefix and Suffix SettingsReader Text Commands Reader Text Commands OnCR3 Maintenance and Troubleshooting General Safety Information Reset Reader to Factory DefaultsWarranty Coverage and Procedure WarrantyLimited Warranty Terms of WarrantyGeneral CR3 AccessoriesTechnical Support and Returns Frequently Asked QuestionsCR3 Maintenance Cleaning the CR3 Window
Top Page Image Contents