Code Alarm CR3 manual VGA & Megapixel Settings, Mirror Decoding, Codes Enable Sxga 1280 x

Page 60

5.4 - VGA & Megapixel Settings

User’s may optimize the CR3’s megapixel (SXGA) imager (1280 x 1024) to VGA (640 x 480). This feature is used to decrease the pixel sampling area, which will greatly increase processing speed. This is an advanced feature used for the rapid decoding of 1-dimensional/linear codes and larger module size 2- dimensional codes. Code recommends testing this feature, as it will not work well with many high density

codes.

Enable SXGA - 1280 x 1024

Enable DOT (Default)

Enable VGA - 640 x 480

5.5 - Mirror Decoding

Scan the following codes to enable/disable the mirroring feature:

On

Off (Default)

Note: The Mirroring feature allows the CR3 to read codes as they are seen through a mirror (inversed 180°). If the Mirroring feature is enabled, all other code reading ability will be disabled.

Save Settings

C002332_09_CR3 User Manual - 54

 

 

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Manual Version Statement of Agency Compliance Laser/LED RadiationSave Settings Table of Contents CR3 Programming Symbology Settings Reader Feedback and Special SettingsAdding a Prefix or Suffix and Reader Text Commands CR3 Maintenance and TroubleshootingAdvanced Decode Performance Getting Started Introduction Powering On/Off Reader UnpackingKeypad/Icon Overview Description of Button FunctionPower Icons Icon DescriptionRS232 Batch Cable-Detect Default Batch OperationIntroduction RS232 Considerations Cabled Operation IntroductionUSB Cable Installation Guide USB Keyboard ModeUSB Communication Settings USB Virtual COM 1 Way ModeReset to USB Factory Defaults USB Keyboard USB DownloaderPS2 Cable Installation Guide PS2 Communication SettingsPS2 Mode Save Settings RS232 Cable Installation Guide Mode RS232 One Way ModeBaud Rate Stop Bits Data Bits Parity NoneRS232 Communication Data Bit Settings RS232 Communication Stop Bit SettingsRS232 Communication Baud Rate Settings RS232 Communication Parity SettingsCabled Reader Time Out Settings Cabled 2 hours Cabled Always DefaultBluetooth Radio Operation Example Reset to RF Factory Defaults QuickConnectRF One Way Mode Max Range RF Two Way ModeBluetooth Radio Auto Connect Bluetooth DisconnectBluetooth Radio Auto Connect On Default Bluetooth Radio Auto Disconnect Bluetooth Radio Time Out Settings Uncabled OperationsBluetooth Radio Out of Range Notification Settings Bluetooth Radio Reader Feedback GuideRS232 To read a symbol with the CR3 Targeting and Reading TechniquesImager Field of View and Resolution Decode Zone BH1 or BH2 Battery Handle Attaching HandlesH1 Handle Reader Battery Installation Attaching and Detaching the Lithium Ion BatteryOptimization and Trigger Programming Introduction DOTGlobal Trigger Optimization Matrix Read Codes with Both Imagers Default Left Trigger Optimization MatrixLeft Trigger Programming Read with Near-Field Imager onlyRight Trigger Optimization Matrix Right Trigger ProgrammingRead Code with Near-Field Imager only Handle Optimization Matrix Handle Trigger ProgrammingFar Field Only On Off Default Continuous Trigger OptimizationContinuous Scan Both Near & Far Field OnContinuous Scan Settings Motion Detection Scan SettingsContinuous Scan Trigger Delays Continuous Scan Sleep Time OutCR3 Programming Symbology Settings Aztec Symbology Codabar SymbologyCodablock F Symbology Code 11 SymbologyCode 39 Symbology Codablock F On Codablock F Off DefaultCode 93 Symbology Code 128 SymbologyCode 93 On Default Code 93 Off Sample Trioptic CodeComposite Symbologies Data Matrix SymbologyGoCode Symbology Interleaved 2 of 5 Symbology Maxicode SymbologyMatrix 2 of 5 Symbology MSI Plessy SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 Symbology NEC 2 of 5 On NEC 2 of 5 Off DefaultPostal Symbologies Royal Mail On Disable All Postal Codes DefaultPharmacode Australian Post On Japan Post OnQR Code Symbology RSS SymbologyTelepen Symbology UPC/EAN/JANReader Feedback and Special Settings Volume and Vibration Settings Off Default Low MediumCode Readability Index Vibrate On / Beep On Vibrate On / Beep OffBacklight Intensity Settings Readability Index Output DisableLow Med Default High Backlight Timeout Settings Laser SettingsReader Power Off Settings Reader Settings Lock Reader Settings LockedReader ID and Firmware Version Reader ID and FirmwareTime Stamp Settings US English Default US English LeadingKeyboard Support No Leading French GermanLock-out Link Mode Reader ID Firmware Version Lockout Link ModeAdvanced Decode Performance Default Enable Continuous IlluminationContinuous Illumination Set Targeting Zone TolerancesWindowing Large 2-Dimensional Codes 640 x 640 pixels VGA & Megapixel Settings Codes Enable Sxga 1280 xEnable VGA 640 x Mirror DecodingAdding a Prefix or Suffix and Reader Text Commands Prefix Settings Suffix SettingsPrefix Comma Prefix Space Erase Prefix and Suffix Settings Reader Text CommandsReader Text Commands On Erase Prefix & Suffix DataCR3 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety InformationWarranty Limited WarrantyTerms of Warranty Warranty Coverage and ProcedureCR3 Accessories GeneralFrequently Asked Questions CR3 MaintenanceCleaning the CR3 Window Technical Support and Returns
Top Page Image Contents