Code Alarm CR3 manual Limited Warranty, Terms of Warranty, Exclusions

Page 66

Lithium Ion Battery - Warning: Charge the battery with Code cables ONLY. Do not open battery, dispose of in fi re, or short circuit - it may ignite, explode, leak, or get hot causing personal injury.

7.3 - Warranty

Code Corporation’s Code Reader 3.0 carries a two year limited warranty as described herein.

Customers may purchase a one or two year extension to this warranty. Please contact a Code representative for more information.

Limited Warranty

Code manufactures its hardware products in accordance with industry-standard practices. Code warrants its products will be free from defects in materials and workmanship, provided that the products are used under normal operating condition intended by the Manufacturer. This warranty is provided to the original owner only and is not transferable to any third party. This warranty is subject to any and all accompanying disclaimers, limitations and other terms of this section.

Terms of Warranty

Code Reader 3.0 units carry a warranty of two years. Other products with serial numbers, such as but not limited to Code Reader 2.0 units, radios, CodeXML modems, battery chargers, stands and power supplies are warranted for three years from date of shipment. Batteries and battery handles carry a two year warranty, or until battery capacity after recharge is less than sixty percent of new, whichever is shortest. Non-serialized items, such as but not limited to handles and cables, carry a 90-day limited warranty.

Exclusions

No warranty herein contained or set out shall apply to any product (i) which has been repaired, altered or tampered with unless done or approved by Code, (ii) which has not been maintained in accordance with any operating or handling instructions supplied by Code, (iii) which has been subjected to unusual physical or electrical stress, immersion in fl uids, puncture, crushing, misuse, abuse, power shortage, improper power supply such as incorrect voltage or wrong polarity, negligence or accident, or (iv) which has been used other than in accordance with the product operating and handling instructions. Preventive maintenance is the responsibility of the customer and is not covered under this warranty.

Warranty Coverage and Procedure

During the warranty period, Code will repair or replace defective products returned to Code’s service center in the US. For worldwide warranty service call Code Warranty Support at 1-801-495-2200.

If warranty service is required, Code will issue a Return Material Authorization Number. Products must be shipped in the original or comparable packaging, with shipping and insurance charges prepaid. Code will ship the repaired or replacement product freight and insurance prepaid in North America. Shipments from the US or other locations will be made F.O.B. Code’s manufacturing plant. Code will use new or refurbished parts at its discretion and will own all parts removed from repaired

Save Settings

C002332_09_CR3 User Manual - 60

Image 66
Contents Manual Version Statement of Agency Compliance Laser/LED RadiationSave Settings Table of Contents CR3 Programming Symbology Settings Reader Feedback and Special SettingsAdding a Prefix or Suffix and Reader Text Commands CR3 Maintenance and TroubleshootingAdvanced Decode Performance Getting Started Introduction Powering On/Off Reader UnpackingKeypad/Icon Overview Description of Button FunctionPower Icons Icon DescriptionRS232 Batch Cable-Detect Default Batch OperationIntroduction RS232 Considerations Cabled Operation IntroductionUSB Cable Installation Guide USB Keyboard ModeReset to USB Factory Defaults USB Communication SettingsUSB Virtual COM 1 Way Mode USB Keyboard USB DownloaderPS2 Cable Installation Guide PS2 Communication SettingsPS2 Mode Save Settings Baud Rate RS232 Cable Installation GuideMode RS232 One Way Mode Stop Bits Data Bits Parity NoneRS232 Communication Baud Rate Settings RS232 Communication Data Bit SettingsRS232 Communication Stop Bit Settings RS232 Communication Parity SettingsCabled Reader Time Out Settings Cabled 2 hours Cabled Always DefaultBluetooth Radio Operation Example Reset to RF Factory Defaults QuickConnectRF One Way Mode Max Range RF Two Way ModeBluetooth Radio Auto Connect Bluetooth DisconnectBluetooth Radio Auto Connect On Default Bluetooth Radio Auto Disconnect Bluetooth Radio Time Out Settings Uncabled OperationsBluetooth Radio Out of Range Notification Settings Bluetooth Radio Reader Feedback GuideRS232 To read a symbol with the CR3 Targeting and Reading TechniquesImager Field of View and Resolution Decode Zone BH1 or BH2 Battery Handle Attaching HandlesH1 Handle Reader Battery Installation Attaching and Detaching the Lithium Ion BatteryOptimization and Trigger Programming Introduction DOTGlobal Trigger Optimization Matrix Left Trigger Programming Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Read with Near-Field Imager onlyRight Trigger Optimization Matrix Right Trigger ProgrammingRead Code with Near-Field Imager only Handle Optimization Matrix Handle Trigger ProgrammingContinuous Scan Far Field Only On Off DefaultContinuous Trigger Optimization Both Near & Far Field OnContinuous Scan Trigger Delays Continuous Scan SettingsMotion Detection Scan Settings Continuous Scan Sleep Time OutCR3 Programming Symbology Settings Aztec Symbology Codabar SymbologyCode 39 Symbology Codablock F SymbologyCode 11 Symbology Codablock F On Codablock F Off DefaultCode 93 On Default Code 93 Off Code 93 SymbologyCode 128 Symbology Sample Trioptic CodeComposite Symbologies Data Matrix SymbologyGoCode Symbology Interleaved 2 of 5 Symbology Maxicode SymbologyMatrix 2 of 5 Symbology MSI Plessy SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 Symbology NEC 2 of 5 On NEC 2 of 5 Off DefaultPharmacode Postal SymbologiesRoyal Mail On Disable All Postal Codes Default Australian Post On Japan Post OnQR Code Symbology RSS SymbologyTelepen Symbology UPC/EAN/JANReader Feedback and Special Settings Code Readability Index Volume and Vibration SettingsOff Default Low Medium Vibrate On / Beep On Vibrate On / Beep OffBacklight Intensity Settings Readability Index Output DisableLow Med Default High Backlight Timeout Settings Laser SettingsReader Power Off Settings Reader ID and Firmware Version Reader Settings LockReader Settings Locked Reader ID and FirmwareKeyboard Support Time Stamp SettingsUS English Default US English Leading No Leading French GermanLock-out Link Mode Reader ID Firmware Version Lockout Link ModeAdvanced Decode Performance Continuous Illumination DefaultEnable Continuous Illumination Set Targeting Zone TolerancesWindowing Large 2-Dimensional Codes 640 x 640 pixels Enable VGA 640 x VGA & Megapixel SettingsCodes Enable Sxga 1280 x Mirror DecodingAdding a Prefix or Suffix and Reader Text Commands Prefix Settings Suffix SettingsPrefix Comma Prefix Space Reader Text Commands On Erase Prefix and Suffix SettingsReader Text Commands Erase Prefix & Suffix DataCR3 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety InformationTerms of Warranty WarrantyLimited Warranty Warranty Coverage and ProcedureCR3 Accessories GeneralCleaning the CR3 Window Frequently Asked QuestionsCR3 Maintenance Technical Support and Returns