Code Alarm CR3 manual Pharmacode, Postal Symbologies, Australian Post On Japan Post On

Page 46

3.19 - Pharmacode

For an explanation of Pharmacode settings and all programming codes please refer to Appendix

G of the CR3 User Manual. You may download the Appendix G at:

www.codecorp.com/support/usermanuals.htm

3.20 - Postal Symbologies

All postal code default settings are OFF. Scan the following codes to enable the appropriate Postal sym- bology:

Note: If you wish to change which Postal code is activated, you MUST first scan the disable all postal codes symbol and then scan your desired symbology.

Australian Post On

Japan Post On

KIX

Planet On

Postnet On

Postnet and Planet On

Royal Mail On

Disable All Postal Codes (Default)

Sample Postnet Code

Save Settings

C002332_09_CR3 User Manual - 40

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Manual Version Statement of Agency Compliance Laser/LED RadiationSave Settings Table of Contents CR3 Programming Symbology Settings Reader Feedback and Special SettingsCR3 Maintenance and Troubleshooting Adding a Prefix or Suffix and Reader Text CommandsAdvanced Decode Performance Getting Started Introduction Powering On/Off Reader UnpackingKeypad/Icon Overview Description of Button FunctionPower Icons Icon DescriptionBatch Operation RS232 Batch Cable-Detect DefaultIntroduction RS232 Considerations Cabled Operation IntroductionUSB Cable Installation Guide USB Keyboard ModeReset to USB Factory Defaults USB Communication SettingsUSB Virtual COM 1 Way Mode USB Keyboard USB DownloaderPS2 Communication Settings PS2 Cable Installation GuidePS2 Mode Save Settings Baud Rate RS232 Cable Installation GuideMode RS232 One Way Mode Stop Bits Data Bits Parity NoneRS232 Communication Baud Rate Settings RS232 Communication Data Bit SettingsRS232 Communication Stop Bit Settings RS232 Communication Parity SettingsCabled Reader Time Out Settings Cabled 2 hours Cabled Always DefaultBluetooth Radio Operation Example Reset to RF Factory Defaults QuickConnectRF One Way Mode Max Range RF Two Way ModeBluetooth Disconnect Bluetooth Radio Auto ConnectBluetooth Radio Auto Connect On Default Bluetooth Radio Time Out Settings Uncabled Operations Bluetooth Radio Auto DisconnectBluetooth Radio Out of Range Notification Settings Reader Feedback Guide Bluetooth RadioRS232 To read a symbol with the CR3 Targeting and Reading TechniquesImager Field of View and Resolution Decode Zone Attaching Handles BH1 or BH2 Battery HandleH1 Handle Reader Battery Installation Attaching and Detaching the Lithium Ion BatteryOptimization and Trigger Programming Introduction DOTGlobal Trigger Optimization Matrix Left Trigger Programming Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Read with Near-Field Imager onlyRight Trigger Programming Right Trigger Optimization MatrixRead Code with Near-Field Imager only Handle Optimization Matrix Handle Trigger ProgrammingContinuous Scan Far Field Only On Off DefaultContinuous Trigger Optimization Both Near & Far Field OnContinuous Scan Trigger Delays Continuous Scan SettingsMotion Detection Scan Settings Continuous Scan Sleep Time OutCR3 Programming Symbology Settings Aztec Symbology Codabar SymbologyCode 39 Symbology Codablock F SymbologyCode 11 Symbology Codablock F On Codablock F Off DefaultCode 93 On Default Code 93 Off Code 93 SymbologyCode 128 Symbology Sample Trioptic CodeData Matrix Symbology Composite SymbologiesGoCode Symbology Interleaved 2 of 5 Symbology Maxicode SymbologyMSI Plessy Symbology Matrix 2 of 5 SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 Symbology NEC 2 of 5 On NEC 2 of 5 Off DefaultPharmacode Postal SymbologiesRoyal Mail On Disable All Postal Codes Default Australian Post On Japan Post OnQR Code Symbology RSS SymbologyTelepen Symbology UPC/EAN/JANReader Feedback and Special Settings Code Readability Index Volume and Vibration SettingsOff Default Low Medium Vibrate On / Beep On Vibrate On / Beep OffReadability Index Output Disable Backlight Intensity SettingsLow Med Default High Laser Settings Backlight Timeout SettingsReader Power Off Settings Reader ID and Firmware Version Reader Settings LockReader Settings Locked Reader ID and FirmwareKeyboard Support Time Stamp SettingsUS English Default US English Leading No Leading French GermanLock-out Link Mode Reader ID Firmware Version Lockout Link ModeAdvanced Decode Performance Continuous Illumination DefaultEnable Continuous Illumination Set Targeting Zone TolerancesWindowing Large 2-Dimensional Codes 640 x 640 pixels Enable VGA 640 x VGA & Megapixel SettingsCodes Enable Sxga 1280 x Mirror DecodingAdding a Prefix or Suffix and Reader Text Commands Suffix Settings Prefix SettingsPrefix Comma Prefix Space Reader Text Commands On Erase Prefix and Suffix SettingsReader Text Commands Erase Prefix & Suffix DataCR3 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety InformationTerms of Warranty WarrantyLimited Warranty Warranty Coverage and ProcedureCR3 Accessories GeneralCleaning the CR3 Window Frequently Asked QuestionsCR3 Maintenance Technical Support and Returns
Top Page Image Contents