Hand Held Products 3700 CCD manual SET-UP and Installation, General Preparation for Use

Page 19

SET–UP AND INSTALLATION

3

 

 

 

 

3.1Introduction

This chapter explains the SCANTEAM 3700 Machine Mount CCD set–up for use in the design lab and a brief description of installation in a host instrument. The set–up procedures are intended for a technician or design engineer to explore the functions and features of the 3700 Machine Mount CCD in a hands–on setting, before the 3700 is embedded in host equipment. The section on installation in a host instrument includes the general mounting dimensions of the 3700.

Set–up and installation includes unpacking the unit, checking for possible damage during shipment, and connecting the Machine Mount CCD to the host system. The host system in the design lab will typically be a PC/DOS microcomputer with an RS–232 communications port and a serial communications program. Otherwise, the host system is the instrument or equipment the 3700 is intended to be embedded in.

A Hand Held Products representative will provide application support if needed. Refer to Chapter 5 for Hand Held Products’ service and technical assistance phone number(s).

3.2General Preparation for Use

Upon receipt, open the carton. Keep the shipping carton since this should be used in the event the scanner ever needs to be returned to the factory for service or repair.

Check the part numbers and confirm that each item on the packing list has been supplied. Check that the scanner model number and any other companion products are the ones ordered for your application. The scanner model and serial numbers are on the identification label attached to the scanner enclosure. Refer to Figure 3.1. You may want to record these numbers for easy reference when communicating with Hand Held Products or your Sales Representative.

Thoroughly inspect the 3700 to determine if any damage has occurred during shipment. Any damage should be reported immediately to the carrier that delivered the 3700. Damage claims due to handling during shipping should be placed directly with the carrier. Hand Held Products will quote for repair of shipment damage (refer to Chapter 5), but the final claim and negotiations with the carrier are the responsibility of the purchaser.

When all the components of your order have been identified and checked, prepare the 3700 for service using the procedures provided in the following sections (for set–up in a design lab or for installation in host equipment). To assure proper operation and prevent possible damage to the 3700 or your host system, perform the following set–up procedures in the sequence in which they are presented.

Note: Before starting the set–up or installation procedure, set the host system or computer power switch to the “OFF” position.

Set–Up and Installation

3–1

Page 18 Page 20
Image 19
Page 18 Page 20
Contents SCANTEAMR3700 CCD Disclaimer Patents Page Table of Contents Chapter Configuring the Scanteam Ascii Conversion Table Technical SpecificationsSerial Commands Summary CCD Operation and Bar Code ScanningList of Tables Intended Audience PrefaceOverview of the Technical Manual Related Publications Introduction Scanteam 3700 DescriptionScanteam 3700 Hardware Description Interface Port Scanteam 3700 Software DescriptionNonvolatile Memory Basic System Operation System Hardware DescriptionMechanical Layout General CharacteristicsMounting Inserts Single Modular Input /Output/Power PortAudible Indicator Operating TheoryCommunications Port Scanner/Host CommunicationAsynchronous Serial Ascii Interface Auxiliary Trigger Hardwire PinoutsPower Requirements General Preparation for Use SET-UP and InstallationSet-up Checklist Set-up Procedure for EvaluationPreparation To setup serial communications to the scanner Set-up ProcedureInstallation in the Host Instrument Top View Examples of Scanteam 3700 Barcode Orientation Pitch or Roll Scanner Illumination Clearance Preparation Configuring the ScanteamCommand Format Command ConventionsData string Enable Decoding Command DC2 Operational CommandsReset Command a Disable Decoding Command DC4Serial Trigger 3C 31 3E Serial Trigger CommandSave Configuration Command Z Save Configuration 3C 5A 3EConfiguration Commands Command Ka baud, parity, stop bits, data bits Parameter Set Communications Port Command KaOption Code ID Value Definition Command Kd enable, data ParameterScanteam 3700 Code ID Values Command Ke enable, data Parameter Set Postamble Command KeCommand Kf mode Parameter Set Communications Protocol Command KfCommand Kg modeglobal, modeport1, modeport2, # Parameter Set Trigger Mode Command KgSet Read Timeout Command Kh Command Kk enable, data Parameter Set No Read Message Command KkSet Votes Command Km Set Code 39 Command Kp Command Ks enable UPC, enable EAN Parameter Set UPC A/E, EAN 8/13 Command KsSet Beeper Mode Command Ku Set Code 128 Command KtSet Scan Rate Command Kv Configuration Status Query Commands Default Configuration Settings Default Operating ParametersDefault Configuration Symbology Settings Troubleshooting Hints SERVICE/TECHNICAL AssistanceMaintenance Troubleshooting GuideScanteam 3700 Troubleshooting Checklist Diagnostic ProcedureTroubleshooting Checklist Problem Possible Cause SolutionProduct Service Department Obtaining Factory ServiceOut Of Warranty Service Service Under WarrantyHelp Desk Followed during installation Chapter Scanteam 3700 Removal/ReplacementService/Technical Assistance CCD Operation and BAR Code Scanning a Scanning and Decoding a Bar Code SymbolObjectives CCD Sensor LED ReflectorPeak Detectors and Comparator Timing Sequence MicroprocessorBar Code Basics and Scanning Tips Closer Look At Bar Code SymbolsBar Code Scanning Optical Specifications Technical SpecificationsScanner Performance Light Source Illumination MRD minimum reflective difference 37.5%Skew Angle Pitch AngleElectrical Specifications Mechanical Specifications Environmental SpecificationsBar Code Symbol Specifications To Host System Scanteam 3700 Interface CableCommand Format Serial Commands SummaryKd? CommandFormatIndividual Configuration Query Ka?Configuration CommandDefault Settings Default Configuration SettingsSymbology Configuration Default Settings Serial Commands Summary Control Function Definitions Ascii Conversion TableAscii Conversion Table Scanteam 3700 Glossary Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Scanteam Index-3 Index-4 Scanteam 3700 Limited Warranty Jordan Road Box Skaneateles Falls, New York 3700/TM Rev E
Top Page Image Contents