Hand Held Products 3700 CCD manual Configuring the Scanteam, Preparation

Page 27

CONFIGURING THE SCANTEAM 3700

4

 

 

 

 

4.1Preparation

This chapter provides instructions for configuring the software in the SCANTEAM 3700 Machine Mount CCD. The configuration process allows you to change the operating parameters of the scanner software to explore the functions of the 3700. The user–defined configuration is stored in volatile RAM memory and can be changed by the user.

All communication between the host system and the 3700 Machine Mount CCD is through the RS–232 communications interface using an Asynchronous ASCII protocol. The host system sends commands one at a time to the 3700. During the configuration process, there is no acknowledgement or other response from the 3700. It is important to enter commands accurately. If a command is sent erroneously to the 3700, you may terminate that command and send the command again. You may send configuration status query commands to obtain a status listing of the configuration selections.

For detailed instructions on preparing the SCANTEAM 3700 for configuration, refer to section 3.3, Set–up Procedure for Use in the Design Lab, or section 3.4, Installation in the Host Instrument.

The application–specific features that can be modified using the RS–232 communication line include the following:

Auditory feedback for operator

Bar code symbology may be disabled for security reasons

Communications parameters

Data message options

Decoding enabled or disabled

Fully configurable bar code symbologies and their options

Triggering options.

Configuring the SCANTEAM 3700

4–1

Image 27
Contents SCANTEAMR3700 CCD Disclaimer Patents Page Table of Contents Chapter Configuring the Scanteam Ascii Conversion Table Technical SpecificationsSerial Commands Summary CCD Operation and Bar Code ScanningList of Tables Preface Intended AudienceOverview of the Technical Manual Related Publications Scanteam 3700 Description IntroductionScanteam 3700 Hardware Description Scanteam 3700 Software Description Interface PortNonvolatile Memory Basic System Operation System Hardware DescriptionMechanical Layout General CharacteristicsMounting Inserts Single Modular Input /Output/Power PortAudible Indicator Operating TheoryScanner/Host Communication Communications PortAsynchronous Serial Ascii Interface Auxiliary Trigger Hardwire PinoutsPower Requirements General Preparation for Use SET-UP and InstallationSet-up Procedure for Evaluation Set-up ChecklistPreparation To setup serial communications to the scanner Set-up ProcedureInstallation in the Host Instrument Top View Examples of Scanteam 3700 Barcode Orientation Pitch or Roll Scanner Illumination Clearance Preparation Configuring the ScanteamCommand Conventions Command FormatData string Enable Decoding Command DC2 Operational CommandsReset Command a Disable Decoding Command DC4Serial Trigger 3C 31 3E Serial Trigger CommandSave Configuration Command Z Save Configuration 3C 5A 3EConfiguration Commands Set Communications Port Command Ka Command Ka baud, parity, stop bits, data bits ParameterOption Command Kd enable, data Parameter Code ID Value DefinitionScanteam 3700 Code ID Values Command Ke enable, data Parameter Set Postamble Command KeCommand Kf mode Parameter Set Communications Protocol Command KfSet Trigger Mode Command Kg Command Kg modeglobal, modeport1, modeport2, # ParameterSet Read Timeout Command Kh Set No Read Message Command Kk Command Kk enable, data ParameterSet Votes Command Km Set Code 39 Command Kp Command Ks enable UPC, enable EAN Parameter Set UPC A/E, EAN 8/13 Command KsSet Code 128 Command Kt Set Beeper Mode Command KuSet Scan Rate Command Kv Configuration Status Query Commands Default Operating Parameters Default Configuration SettingsDefault Configuration Symbology Settings Troubleshooting Hints SERVICE/TECHNICAL AssistanceMaintenance Troubleshooting GuideScanteam 3700 Troubleshooting Checklist Diagnostic ProcedureTroubleshooting Checklist Problem Possible Cause SolutionProduct Service Department Obtaining Factory ServiceService Under Warranty Out Of Warranty ServiceHelp Desk Followed during installation Chapter Scanteam 3700 Removal/ReplacementService/Technical Assistance Scanning and Decoding a Bar Code Symbol CCD Operation and BAR Code Scanning aObjectives LED Reflector CCD SensorPeak Detectors and Comparator Timing Sequence MicroprocessorCloser Look At Bar Code Symbols Bar Code Basics and Scanning TipsBar Code Scanning Technical Specifications Optical SpecificationsScanner Performance Light Source Illumination MRD minimum reflective difference 37.5%Skew Angle Pitch AngleElectrical Specifications Mechanical Specifications Environmental SpecificationsBar Code Symbol Specifications To Host System Scanteam 3700 Interface CableCommand Format Serial Commands SummaryKd? CommandFormatIndividual Configuration Query Ka?Default Configuration Settings Configuration CommandDefault SettingsSymbology Configuration Default Settings Serial Commands Summary Control Function Definitions Ascii Conversion TableAscii Conversion Table Scanteam 3700 Glossary Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Scanteam Index-3 Index-4 Scanteam 3700 Limited Warranty Jordan Road Box Skaneateles Falls, New York 3700/TM Rev E