Hand Held Products 3700 CCD Set No Read Message Command Kk, Command Kk enable, data Parameter

Page 37

Set No Read Message Command Kk
COMMAND <Kk enable, data>
Parameter	ASCII	Option
Enable	0	no
	1	yes * (NR)
Data		one to seven ASCII characters

Sending the configuration command Kk sets the no read message. Any ASCII character can be specified except NUL, ACK, NAK, DC1, DC2, DC3, DC4 or DEL. The default setting is NR (no read).

Tip: The No Read Message is not sent for scanner ports that are configured for a continuous trigger mode.

Set Votes Command Km

COMMAND <Km data_global, data_port_1, data_port_2, #>

Parameter ASCII	Option
Data	one or two ASCII digits
	range of 1 to 31 * (3, 1)

Sending the configuration command Km sets the votes. One or two ASCII digits in the range of 1 to 31 determine the number of consecutive identical decodes required for a valid read. A selection of 1 means that no voting will take place. The default setting is Data_port_1, 3 and Data_port_2, 1, which means voting is set to 3 for port 1 and set to 1 for port 2.

Tip: When using the voting feature for additional decode security, a value of three is generally adequate in most applications.

Configuring the SCANTEAM 3700

4–11

Image 37

Contents SCANTEAMR3700 CCD Disclaimer Patents Page Table of Contents Chapter Configuring the Scanteam Serial Commands Summary Technical SpecificationsCCD Operation and Bar Code Scanning Ascii Conversion TableList of Tables Intended Audience PrefaceOverview of the Technical Manual Related Publications Introduction Scanteam 3700 DescriptionScanteam 3700 Hardware Description Interface Port Scanteam 3700 Software DescriptionNonvolatile Memory Basic System Operation System Hardware DescriptionMechanical Layout General CharacteristicsAudible Indicator Single Modular Input /Output/Power PortOperating Theory Mounting InsertsCommunications Port Scanner/Host CommunicationAsynchronous Serial Ascii Interface Auxiliary Trigger Hardwire PinoutsPower Requirements General Preparation for Use SET-UP and InstallationSet-up Checklist Set-up Procedure for EvaluationPreparation To setup serial communications to the scanner Set-up ProcedureInstallation in the Host Instrument Top View Examples of Scanteam 3700 Barcode Orientation Pitch or Roll Scanner Illumination Clearance Preparation Configuring the ScanteamCommand Format Command ConventionsData string Reset Command a Operational CommandsDisable Decoding Command DC4 Enable Decoding Command DC2Save Configuration Command Z Serial Trigger CommandSave Configuration 3C 5A 3E Serial Trigger 3C 31 3EConfiguration Commands Command Ka baud, parity, stop bits, data bits Parameter Set Communications Port Command KaOption Code ID Value Definition Command Kd enable, data ParameterScanteam 3700 Code ID Values Command Ke enable, data Parameter Set Postamble Command KeCommand Kf mode Parameter Set Communications Protocol Command KfCommand Kg modeglobal, modeport1, modeport2, # Parameter Set Trigger Mode Command KgSet Read Timeout Command Kh Command Kk enable, data Parameter Set No Read Message Command KkSet Votes Command Km Set Code 39 Command Kp Command Ks enable UPC, enable EAN Parameter Set UPC A/E, EAN 8/13 Command KsSet Beeper Mode Command Ku Set Code 128 Command KtSet Scan Rate Command Kv Configuration Status Query Commands Default Configuration Settings Default Operating ParametersDefault Configuration Symbology Settings Maintenance SERVICE/TECHNICAL AssistanceTroubleshooting Guide Troubleshooting HintsTroubleshooting Checklist Diagnostic ProcedureProblem Possible Cause Solution Scanteam 3700 Troubleshooting ChecklistProduct Service Department Obtaining Factory ServiceOut Of Warranty Service Service Under WarrantyHelp Desk Followed during installation Chapter Scanteam 3700 Removal/ReplacementService/Technical Assistance CCD Operation and BAR Code Scanning a Scanning and Decoding a Bar Code SymbolObjectives CCD Sensor LED ReflectorPeak Detectors and Comparator Timing Sequence MicroprocessorBar Code Basics and Scanning Tips Closer Look At Bar Code SymbolsBar Code Scanning Optical Specifications Technical SpecificationsScanner Performance Skew Angle MRD minimum reflective difference 37.5%Pitch Angle Light Source IlluminationElectrical Specifications Mechanical Specifications Environmental SpecificationsBar Code Symbol Specifications To Host System Scanteam 3700 Interface CableCommand Format Serial Commands SummaryIndividual Configuration Query CommandFormatKa? Kd?Configuration CommandDefault Settings Default Configuration SettingsSymbology Configuration Default Settings Serial Commands Summary Control Function Definitions Ascii Conversion TableAscii Conversion Table Scanteam 3700 Glossary Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Scanteam Index-3 Index-4 Scanteam 3700 Limited Warranty Jordan Road Box Skaneateles Falls, New York 3700/TM Rev E