Printronix T5000e Series user manual Validator Statistics

Page 47

Validator Statistics

5.Press + or to cycle through the choices:

Short Report. Default setting. Provides the encoded failure cause or pass indication and the bar width deviation, shown as a percentage.

Full Report. Provides a completed report of all the data captured by the validator.

Validation Mode. Provides the same data as the Short Report, but adds the actual bar code data read.

6.When your selection displays, press to activate it.

7.Press and at the same time to lock the key, then press PAUSE to take the printer offline.

8.Press PAUSE again to put the printer online.

Validator Statistics

The validator displays a number of statistics directly on the printer LCD, without having to print a report. To view any of the statistics:

.

1. Press .. to take the printer offline and place the printer in Menu mode.

2. If necessary, press and at the same time to unlock the key.

.

3. If necessary, press .. until “VALIDATOR” displays.

4. Press to scroll through the following statistics on the printer display:

Good Barcodes: The number of bar code reports sent from the validator since the last Clear Data command.

Good Forms: The number of forms printed since the last Clear Data command.

Overstrike Forms: The number of forms containing a bar code that fell below the minimum acceptable level since the last Clear Data command.

Average BWD: The average of all Bar Width Deviations reported since the last Clear Data command, shown as a percentage.

47

Image 47
Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Definitions Software License AgreementTermination of License Agreement Communication NoticesEuropean Community EC Conformity Statement Page Trademark Acknowledgements Table of Contents Table of Contents Operational Parameters OverviewOverview Tools And Materials You Will Need Parts ListSafety Notices Safety NoticesPrepare The Printer InstallationPrepare The Printer Installation Install The FerriteRemoving the Expansion-CT Subassembly Install The FerriteWrapping the Power/Data Cable Around the Ferrite Inserting the Wire Saddle Into the Frame Boss Wire Saddle Long Connector To Validator Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Install The BracketsValidator Rear View Hash Marks Lower Bracket Upper Attach The Power/Data Cable To The Validator Attach The Power/Data Cable To The ValidatorRestore The Printer To Operation Restore The Printer To OperationEnable The Validator Adjust The Scanning Beam Adjust The Scanning BeamAligning the Scanning Beam Peel-Off Media Handling Mode Scanning Beam Adjustment Screws Attach The Power/Data Cable To The Validator Adjusting the Center of the Scanning Beam Shifting The Scanning Beam Shifting The Scanning BeamCalibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Validator Front Panel Basic Validator SetupUnit Positioning Basic Validator Setup Validator Menu Structure Validator Menu StructureCont. from previous Enabling And Disabling The Validator Configuring The ValidatorEnabling And Disabling The Validator Validator ReportingRequesting a Validator Report Setting Auto ReportConfiguring The Validator To enable Auto ReportValidator Reporting Resetting Validator DataDefining The Data Output Destination Telemetry Path Configuring The Validator Validator Statistics Validator StatisticsDefining Validator Options Setting Number Of Bar Codes On a FormDefining Validator Options Setting The Symbol ContrastChecking Quiet Zones Checking The Firmware Revision Number Setting Overstrike Style Setting For Skip LabelsNum Retry Setting I2of5 ChecksumAdvanced Validator Options Advanced Validator OptionsDecodeability Defects Percent DecodeScanner Settings Beam Shift Print Speed Limits OperationPrint Speed Limits Bar Code Height Min. Code HeightTo set the printer speed manually To change the Min. Code HeightTo change the Min. Code Gap Validation Report TypeMin. Code Gap Demand Printing Modes Bar Code Failures Bad Bar Code Error DetectionMissing Bar Code Error Detection Bad Bar Code Error DetectionBar Code Failures Error ActionStop Overstrike Retry Form default StopRetry Form Error ActionOverstrike Message List Explanation Solution Error MessagesError Messages Message List Explanation Solution User’s Manual Bar Code Failures Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution Troubleshooting the Validator Symptom Solution TroubleshootingError Messages Page Maintenance Maintenance Index Index Index Index Page 170895-001