Printronix T5000e Series user manual Scanner Settings

Page 55

Advanced Validator Options

5.Press + or to scroll through the percentage values: 0% to 100%. The default is 20%.

6.Press to select the desired value.

7.Press and at the same time to lock the key, then press PAUSE to take the printer offline.

8.Press PAUSE again to put the printer online.

Scanner Settings

This option has two purposes:

Allows the validator to upload an optimized setting for a particular printer size at power up. This will use the full scanner beam width and improve the performance and efficiency of the validator.

Allows you to customize a special scanner setting for a specific application. The file can then be downloaded to the printer by using normal printer download procedures and must be saved as part of the power up configuration. For more information, contact the Printronix Customer Solutions Center at 714-368- 2686.

To set this option when a special setting has been downloaded:

.

1. Press .. to take the printer offline and place the printer in Menu mode.

2. If necessary, press and at the same time to unlock the key.

.

3. If necessary, press .. until “VALIDATOR” displays.

4. Press until “Scanner Settings” displays.

5. Press + or to scroll through the options: Default or a special file name. Default is the default.

6. Press to accept the desired value.

7. Save this configuration and set it as the Power-Up configuration in the CONFIG CTRL menu.

8. Recycle power for the new setting to take effect.

9. The beam may need to be moved horizontally. See “Beam Shift” on page 56.

55

Image 55
Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Definitions Software License AgreementTermination of License Agreement Communication NoticesEuropean Community EC Conformity Statement Page Trademark Acknowledgements Table of Contents Table of Contents Operational Parameters OverviewOverview Tools And Materials You Will Need Parts ListSafety Notices Safety NoticesPrepare The Printer InstallationPrepare The Printer Installation Install The FerriteRemoving the Expansion-CT Subassembly Install The FerriteWrapping the Power/Data Cable Around the Ferrite Inserting the Wire Saddle Into the Frame Boss Wire Saddle Long Connector To Validator Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Install The BracketsValidator Rear View Hash Marks Lower Bracket Upper Attach The Power/Data Cable To The Validator Attach The Power/Data Cable To The ValidatorRestore The Printer To Operation Restore The Printer To OperationEnable The Validator Adjust The Scanning Beam Adjust The Scanning BeamAligning the Scanning Beam Peel-Off Media Handling Mode Scanning Beam Adjustment Screws Attach The Power/Data Cable To The Validator Adjusting the Center of the Scanning Beam Shifting The Scanning Beam Shifting The Scanning BeamCalibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Unit Positioning Basic Validator SetupValidator Front Panel Basic Validator Setup Validator Menu Structure Validator Menu StructureCont. from previous Enabling And Disabling The Validator Configuring The ValidatorEnabling And Disabling The Validator Validator ReportingRequesting a Validator Report Setting Auto ReportConfiguring The Validator To enable Auto ReportDefining The Data Output Destination Telemetry Path Resetting Validator DataValidator Reporting Configuring The Validator Validator Statistics Validator StatisticsDefining Validator Options Setting Number Of Bar Codes On a FormChecking Quiet Zones Setting The Symbol ContrastDefining Validator Options Checking The Firmware Revision Number Setting Overstrike Style Setting For Skip LabelsNum Retry Setting I2of5 ChecksumDecodeability Advanced Validator OptionsAdvanced Validator Options Defects Percent DecodeScanner Settings Beam Shift Print Speed Limits OperationPrint Speed Limits Bar Code Height Min. Code HeightTo set the printer speed manually To change the Min. Code HeightMin. Code Gap Validation Report TypeTo change the Min. Code Gap Demand Printing Modes Bar Code Failures Bad Bar Code Error DetectionMissing Bar Code Error Detection Bad Bar Code Error DetectionBar Code Failures Error ActionStop Overstrike Retry Form default StopOverstrike Error ActionRetry Form Message List Explanation Solution Error MessagesError Messages Message List Explanation Solution User’s Manual Bar Code Failures Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution Error Messages TroubleshootingTroubleshooting the Validator Symptom Solution Page Maintenance Maintenance Index Index Index Index Page 170895-001