Printronix T5000e Series user manual Setting I2of5 Checksum, Num Retry

Page 52

Chapter 2 Configuring The Validator

6.Press ↵ to select the desired value.

7.Press ↓ and ↵ at the same time to lock the ↵ key, then press PAUSE to take the printer offline.

8.Press PAUSE again to put the printer online.

Setting I2of5 Checksum

This option allows you to include or exclude the checksum option in the Interleaved 2 of 5 code as part of the grading. For example, if you enable this option, then any incoming bar code data without checksum digits will be graded as a failure, and a Checksum Failure error will display.

.

1. Press .. to take the printer offline and place the printer in Menu mode.

2. If necessary, press ↓ and ↵ at the same time to unlock the ↵ key.

.

3. If necessary, press .. until “VALIDATOR” displays.

4. Press ↓ until “I2of5 Checksum” displays.

5. Press + or – to scroll through the options: Enable or Disable. The default is Disable.

6. Press ↵ to accept the desired value.

7. Press ↓ and ↵ at the same time to lock the ↵ key, then press PAUSE to take the printer offline.

8. Press PAUSE again to put the printer online.

Num Retry

This option allows you to set a number of retries for overstrike before the printer stops.

The options are 3, 4, 5, and Infinite. The factory default is 5.

NOTE: This setting is utilized only if Validator Action is set to Retry Form. See “Error Action” on page 62.

For the 3, 4, and 5 options, the printer will stop after the specified number of retry attempts. After you clear the error message, the printer will print the next label.

52

Image 52

Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Software License Agreement DefinitionsCommunication Notices Termination of License AgreementEuropean Community EC Conformity Statement Page Trademark Acknowledgements Table of Contents Table of Contents Overview Operational ParametersOverview Parts List Tools And Materials You Will NeedSafety Notices Safety NoticesPrepare The Printer InstallationPrepare The Printer Install The Ferrite InstallationInstall The Ferrite Removing the Expansion-CT SubassemblyWrapping the Power/Data Cable Around the Ferrite Inserting the Wire Saddle Into the Frame Boss Wire Saddle Long Connector To Validator Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Install The BracketsValidator Rear View Hash Marks Lower Bracket Upper Attach The Power/Data Cable To The Validator Attach The Power/Data Cable To The ValidatorRestore The Printer To Operation Restore The Printer To OperationEnable The Validator Adjust The Scanning Beam Adjust The Scanning BeamAligning the Scanning Beam Peel-Off Media Handling Mode Scanning Beam Adjustment Screws Attach The Power/Data Cable To The Validator Adjusting the Center of the Scanning Beam Shifting The Scanning Beam Shifting The Scanning BeamCalibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Unit Positioning Basic Validator SetupValidator Front Panel Basic Validator Setup Validator Menu Structure Validator Menu StructureCont. from previous Configuring The Validator Enabling And Disabling The ValidatorValidator Reporting Enabling And Disabling The ValidatorSetting Auto Report Configuring The ValidatorTo enable Auto Report Requesting a Validator ReportDefining The Data Output Destination Telemetry Path Resetting Validator DataValidator Reporting Configuring The Validator Validator Statistics Validator StatisticsSetting Number Of Bar Codes On a Form Defining Validator OptionsChecking Quiet Zones Setting The Symbol ContrastDefining Validator Options Checking The Firmware Revision Number Setting For Skip Labels Setting Overstrike StyleSetting I2of5 Checksum Num RetryDecodeability Advanced Validator OptionsAdvanced Validator Options Percent Decode DefectsScanner Settings Beam Shift Operation Print Speed LimitsBar Code Height Min. Code Height Print Speed LimitsTo change the Min. Code Height To set the printer speed manuallyMin. Code Gap Validation Report TypeTo change the Min. Code Gap Demand Printing Modes Bad Bar Code Error Detection Missing Bar Code Error DetectionBad Bar Code Error Detection Bar Code FailuresError Action Stop Overstrike Retry Form defaultStop Bar Code FailuresOverstrike Error ActionRetry Form Error Messages Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution User’s ManualError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution Error Messages TroubleshootingTroubleshooting the Validator Symptom Solution Page Maintenance Maintenance Index Index Index Index Page 170895-001