Printronix T5000e Series user manual Communication Notices, Termination of License Agreement

Page 5

2.IN NO EVENT WILL PRINTRONIX, INC. BE LIABLE FOR LOST PROFITS, LOST DATA, BUSINESS INTERRUPTIONS, OR ANY OTHER DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF OR INABILITY TO USE THIS PRODUCT, EVEN IF PRINTRONIX, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR ANY DAMAGES CAUSED BY THE ABUSE OR MANIPULATION OF THE SOFTWARE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

3.Printronix, Inc. will not be liable for any loss or damage caused by delay in furnishing a Software Product or any other performance under this Agreement.

4.Our entire liability and your exclusive remedies for our liability of any kind (including liability for negligence except liability for personal injury caused solely by our negligence) for the Software Product covered by this Agreement and all other performance or nonperformance by us under or related to this Agreement are limited to the remedies specified by this Agreement.

5.California law governs this Agreement.

Termination of License Agreement

This License shall continue until terminated. This license may be terminated by agreement between you and Printronix, Inc. or by Printronix, Inc. if you fail to comply with the terms of this License and such failure is not corrected within thirty (30) days after notice. When this License is terminated, you shall return to the place you obtained them, the printer and all copies of the Software and documentation.

U.S. Government Restricted Rights

Use, duplication or disclosure by the Government is subject to restrictions as set forth in the Rights in Technical Data and Computer Software clause at FAR 242.227-7013, subdivision (b) (3) (ii) or subparagraph

(c)(1) (ii), as appropriate. Further use, duplication or disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR 52.227-19 (c) (2).

Acknowledgement of Terms and Conditions

YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT, AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. NEITHER PARTY SHALL BE BOUND BY ANY STATEMENT OR REPRESENTATION NOT CONTAINED IN THIS AGREEMENT. NO CHANGE IN THIS AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED BY PROPERLY AUTHORIZED REPRESENTATIVES OF EACH PARTY. BY USING THIS PRINTER, YOU AGREE TO ACCEPT THE TERMS AND CONDITIONS OF THIS AGREEMENT.

Communication Notices

Federal Communications Commission (FCC) Statement: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provided reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Printronix is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by any unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment.

Image 5
Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Definitions Software License AgreementTermination of License Agreement Communication NoticesEuropean Community EC Conformity Statement Page Trademark Acknowledgements Table of Contents Table of Contents Operational Parameters OverviewOverview Tools And Materials You Will Need Parts ListSafety Notices Safety NoticesPrepare The Printer InstallationPrepare The Printer Installation Install The FerriteRemoving the Expansion-CT Subassembly Install The FerriteWrapping the Power/Data Cable Around the Ferrite Inserting the Wire Saddle Into the Frame Boss Wire Saddle Long Connector To Validator Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Install The BracketsValidator Rear View Hash Marks Lower Bracket Upper Attach The Power/Data Cable To The Validator Attach The Power/Data Cable To The ValidatorRestore The Printer To Operation Restore The Printer To OperationEnable The Validator Adjust The Scanning Beam Adjust The Scanning BeamAligning the Scanning Beam Peel-Off Media Handling Mode Scanning Beam Adjustment Screws Attach The Power/Data Cable To The Validator Adjusting the Center of the Scanning Beam Shifting The Scanning Beam Shifting The Scanning BeamCalibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Validator Front Panel Basic Validator SetupUnit Positioning Basic Validator Setup Validator Menu Structure Validator Menu StructureCont. from previous Enabling And Disabling The Validator Configuring The ValidatorValidator Reporting Enabling And Disabling The ValidatorConfiguring The Validator Setting Auto ReportTo enable Auto Report Requesting a Validator ReportValidator Reporting Resetting Validator DataDefining The Data Output Destination Telemetry Path Configuring The Validator Validator Statistics Validator StatisticsDefining Validator Options Setting Number Of Bar Codes On a FormDefining Validator Options Setting The Symbol ContrastChecking Quiet Zones Checking The Firmware Revision Number Setting Overstrike Style Setting For Skip LabelsNum Retry Setting I2of5 ChecksumAdvanced Validator Options Advanced Validator OptionsDecodeability Defects Percent DecodeScanner Settings Beam Shift Print Speed Limits OperationBar Code Height Min. Code Height Print Speed LimitsTo set the printer speed manually To change the Min. Code HeightTo change the Min. Code Gap Validation Report TypeMin. Code Gap Demand Printing Modes Missing Bar Code Error Detection Bad Bar Code Error DetectionBad Bar Code Error Detection Bar Code FailuresStop Overstrike Retry Form default Error ActionStop Bar Code FailuresRetry Form Error ActionOverstrike Message List Explanation Solution Error MessagesError Messages Message List Explanation Solution User’s Manual Bar Code Failures Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution Troubleshooting the Validator Symptom Solution TroubleshootingError Messages Page Maintenance Maintenance Index Index Index Index Page 170895-001