Printronix T5000e Series user manual Index

Page 75

Index

S

Scanner Settings, 55

Setting Auto Report, 44

Setting calibration, 34

Short Report, 46

Skip Labels command, 51

Speed Exceeds / Validator Limit, 67 Speed limits, 57

Statistics

Average BWD, 47

Good Barcodes, 47

Good Forms, 47

Last BWD, 48

Overstrike Forms, 47

Stop Mode, 62

Symbol Contrast command, 49

T

Telemetry Path, 45

Troubleshooting, 69

U

Unscannable code / check media, 68

V

Validation Mode, 46

Validator

Bar Code Demo Page, 36 bar code failure, 61 calibration, 34 configuration, 43 disabling, 43

enabling, 43 error action, 62 installation, 15 maintenance, 71 options, 48, 53 panel, 39 parameters, 11 reporting, 43 statistics, 47

Validator Funct. command, 27, 43 Validator not / communicating, 68 Validator Report command, 44

75

Image 75

Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Definitions Software License AgreementTermination of License Agreement Communication NoticesEuropean Community EC Conformity Statement Page Trademark Acknowledgements Table of Contents Table of Contents Operational Parameters OverviewOverview Tools And Materials You Will Need Parts ListSafety Notices Safety NoticesInstallation Prepare The PrinterPrepare The Printer Installation Install The FerriteRemoving the Expansion-CT Subassembly Install The FerriteWrapping the Power/Data Cable Around the Ferrite Inserting the Wire Saddle Into the Frame Boss Wire Saddle Long Connector To Validator Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Install The BracketsValidator Rear View Hash Marks Lower Bracket Upper Attach The Power/Data Cable To The Validator Attach The Power/Data Cable To The ValidatorRestore The Printer To Operation Restore The Printer To OperationEnable The Validator Adjust The Scanning Beam Adjust The Scanning BeamAligning the Scanning Beam Peel-Off Media Handling Mode Scanning Beam Adjustment Screws Attach The Power/Data Cable To The Validator Adjusting the Center of the Scanning Beam Shifting The Scanning Beam Shifting The Scanning BeamReset Button Settings Time Reset Button Is Depressed Result CalibrationCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Basic Validator Setup Unit PositioningValidator Front Panel Basic Validator Setup Validator Menu Structure Validator Menu StructureCont. from previous Enabling And Disabling The Validator Configuring The ValidatorEnabling And Disabling The Validator Validator ReportingRequesting a Validator Report Setting Auto ReportConfiguring The Validator To enable Auto ReportResetting Validator Data Defining The Data Output Destination Telemetry PathValidator Reporting Configuring The Validator Validator Statistics Validator StatisticsDefining Validator Options Setting Number Of Bar Codes On a FormSetting The Symbol Contrast Checking Quiet ZonesDefining Validator Options Checking The Firmware Revision Number Setting Overstrike Style Setting For Skip LabelsNum Retry Setting I2of5 ChecksumAdvanced Validator Options DecodeabilityAdvanced Validator Options Defects Percent DecodeScanner Settings Beam Shift Print Speed Limits OperationPrint Speed Limits Bar Code Height Min. Code HeightTo set the printer speed manually To change the Min. Code HeightValidation Report Type Min. Code GapTo change the Min. Code Gap Demand Printing Modes Bar Code Failures Bad Bar Code Error DetectionMissing Bar Code Error Detection Bad Bar Code Error DetectionBar Code Failures Error ActionStop Overstrike Retry Form default StopError Action OverstrikeRetry Form Message List Explanation Solution Error MessagesError Messages Message List Explanation Solution User’s Manual Bar Code Failures Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution Troubleshooting Error MessagesTroubleshooting the Validator Symptom Solution Page Maintenance Maintenance Index Index Index Index Page 170895-001