Printronix T5000e Series user manual Checking The Firmware Revision Number

Page 50

Chapter 2 Configuring The Validator

2.If necessary, press ↓ and ↵ at the same time to unlock the ↵ key.

.

3. If necessary, press .. until “VALIDATOR” displays.

4. Press ↓ until “Quiet Zones” displays.

5. Press + or – to scroll through the choices: Enable or Disable. The default is Enable.

6. Press ↵ to select the desired value.

7. Press ↓ and ↵ at the same time to lock the ↵ key, then press PAUSE to take the printer offline.

8. Press PAUSE again to put the printer online.

NOTE: The validator does not recognize x-dimensions greater than 40 mil with Quiet Zones enabled.

Checking The Firmware Revision Number

For troubleshooting purposes, you may need to reference the firmware revision number.

.

1. Press .. to take the printer offline and place the printer in Menu mode.

2. If necessary, press ↓ and ↵ at the same time to unlock the ↵ key.

.

3. If necessary, press .. until “VALIDATOR” displays.

4. Press ↓ until “F/W Revision” displays. The firmware version number displays.

5. Press ↓ and ↵ at the same time to lock the ↵ key, then press PAUSE to take the printer offline.

6. Press PAUSE again to put the printer online.

50

Image 50

Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Software License Agreement DefinitionsCommunication Notices Termination of License AgreementEuropean Community EC Conformity Statement Page Trademark Acknowledgements Table of Contents Table of Contents Overview Operational ParametersOverview Parts List Tools And Materials You Will NeedSafety Notices Safety NoticesPrepare The Printer InstallationPrepare The Printer Install The Ferrite InstallationInstall The Ferrite Removing the Expansion-CT SubassemblyWrapping the Power/Data Cable Around the Ferrite Inserting the Wire Saddle Into the Frame Boss Wire Saddle Long Connector To Validator Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Install The BracketsValidator Rear View Hash Marks Lower Bracket Upper Attach The Power/Data Cable To The Validator Attach The Power/Data Cable To The ValidatorRestore The Printer To Operation Restore The Printer To OperationEnable The Validator Adjust The Scanning Beam Adjust The Scanning BeamAligning the Scanning Beam Peel-Off Media Handling Mode Scanning Beam Adjustment Screws Attach The Power/Data Cable To The Validator Adjusting the Center of the Scanning Beam Shifting The Scanning Beam Shifting The Scanning BeamCalibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Validator Front Panel Basic Validator SetupUnit Positioning Basic Validator Setup Validator Menu Structure Validator Menu StructureCont. from previous Validator Reporting Configuring The ValidatorEnabling And Disabling The Validator Enabling And Disabling The ValidatorTo enable Auto Report Setting Auto ReportConfiguring The Validator Requesting a Validator ReportValidator Reporting Resetting Validator DataDefining The Data Output Destination Telemetry Path Configuring The Validator Validator Statistics Validator StatisticsSetting Number Of Bar Codes On a Form Defining Validator OptionsDefining Validator Options Setting The Symbol ContrastChecking Quiet Zones Checking The Firmware Revision Number Setting For Skip Labels Setting Overstrike StyleSetting I2of5 Checksum Num RetryAdvanced Validator Options Advanced Validator OptionsDecodeability Percent Decode DefectsScanner Settings Beam Shift Bar Code Height Min. Code Height OperationPrint Speed Limits Print Speed LimitsTo change the Min. Code Height To set the printer speed manuallyTo change the Min. Code Gap Validation Report TypeMin. Code Gap Demand Printing Modes Bad Bar Code Error Detection Bad Bar Code Error DetectionMissing Bar Code Error Detection Bar Code FailuresStop Error ActionStop Overstrike Retry Form default Bar Code FailuresRetry Form Error ActionOverstrike Error Messages Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution User’s ManualError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution Troubleshooting the Validator Symptom Solution TroubleshootingError Messages Page Maintenance Maintenance Index Index Index Index Page 170895-001