Printronix T5000e Series user manual Index

Page 73

Index

A

Auto detect bar codes, 48, 61 Auto Report, 44

Average BWD command, 47

B

Bad bar codes, 61

Bar Code Demo Page, 36

Bar code failure, 61

Bar Code Improper / Data Format, 64 Bar code quiet / zone too small, 65 Bar codes supported, 11

Bar width deviation, 47, 53

Beam Shift, 56

BWD, 48

C

Calibration / warning, 65

Calibration, setting, 34

Checksum Failure, 65

Clear Data command, 45

Clear validator data, 45

Configuring, 43

Contrast too low / Check media, 66

D

Decodeability, 53

Defects, 54

Demand printing, 60

Demo Page, 36

Disabling validator, 43

E

Enabling validator, 43

Error action, 62

Overstrike Mode, 63

Retry Form, 63

Stop Mode, 62

Error messages

Bar Code Improper / Data Format, 64 Bar code quiet / zone too small, 65 Calibration / warning, 65 Checksum Failure, 65

Contrast too low / Check media, 66 Poor scanning / Check heat&head, 66 Poor scanning / Check media, 66 Poor scanning / Inspect head, 67 Speed Exceeds / Validator Limit, 67 Unscannable code / check media, 68 Validator not / communicating, 68

External device reporting, 45

73

Image 73
Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Definitions Software License AgreementTermination of License Agreement Communication NoticesEuropean Community EC Conformity Statement Page Trademark Acknowledgements Table of Contents Table of Contents Operational Parameters OverviewOverview Tools And Materials You Will Need Parts ListSafety Notices Safety NoticesPrepare The Printer InstallationPrepare The Printer Installation Install The FerriteRemoving the Expansion-CT Subassembly Install The FerriteWrapping the Power/Data Cable Around the Ferrite Inserting the Wire Saddle Into the Frame Boss Wire Saddle Long Connector To Validator Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Install The BracketsValidator Rear View Hash Marks Lower Bracket Upper Attach The Power/Data Cable To The Validator Attach The Power/Data Cable To The ValidatorRestore The Printer To Operation Restore The Printer To OperationEnable The Validator Adjust The Scanning Beam Adjust The Scanning BeamAligning the Scanning Beam Peel-Off Media Handling Mode Scanning Beam Adjustment Screws Attach The Power/Data Cable To The Validator Adjusting the Center of the Scanning Beam Shifting The Scanning Beam Shifting The Scanning BeamCalibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Unit Positioning Basic Validator SetupValidator Front Panel Basic Validator Setup Validator Menu Structure Validator Menu StructureCont. from previous Enabling And Disabling The Validator Configuring The ValidatorValidator Reporting Enabling And Disabling The ValidatorConfiguring The Validator Setting Auto ReportTo enable Auto Report Requesting a Validator ReportDefining The Data Output Destination Telemetry Path Resetting Validator DataValidator Reporting Configuring The Validator Validator Statistics Validator StatisticsDefining Validator Options Setting Number Of Bar Codes On a FormChecking Quiet Zones Setting The Symbol ContrastDefining Validator Options Checking The Firmware Revision Number Setting Overstrike Style Setting For Skip LabelsNum Retry Setting I2of5 ChecksumDecodeability Advanced Validator OptionsAdvanced Validator Options Defects Percent DecodeScanner Settings Beam Shift Print Speed Limits OperationBar Code Height Min. Code Height Print Speed LimitsTo set the printer speed manually To change the Min. Code HeightMin. Code Gap Validation Report TypeTo change the Min. Code Gap Demand Printing Modes Missing Bar Code Error Detection Bad Bar Code Error DetectionBad Bar Code Error Detection Bar Code FailuresStop Overstrike Retry Form default Error ActionStop Bar Code FailuresOverstrike Error ActionRetry Form Message List Explanation Solution Error MessagesError Messages Message List Explanation Solution User’s Manual Bar Code Failures Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution Error Messages TroubleshootingTroubleshooting the Validator Symptom Solution Page Maintenance Maintenance Index Index Index Index Page 170895-001