Telstrat Argent manual Call Forward, Multiple Subscriber Number MSN

Page 27

Argent Terminal Adaptor - User Guide

5.2.5Call Forward

Call forward allows calls to be forwarded to any other telephone including mobiles either immediately, when busy or if the call is not answered.

5.2.5.1 Call Forward Immediate or Unconditional

Call Forward Immediate also called Call Forward Unconditional (CFU) will direct all incoming phone calls to another phone until the feature is turned off.

a

To turn Call Forward Immediate (Variable Number) ON.

OH * 21

DN # RH

 

 

 

 

b

To turn Call Forward Immediate (Variable or Fixed

OH # 21

# RH

 

Number) OFF.

 

 

 

 

 

c

To check if Call Forward Immediate is ON or OFF

OH * # 21 # RSP RH

 

 

 

 

5.2.5.2 Call Forward On Busy

Call Forward On Busy (CFB) will direct a phone calls to another phone when the line is in use.

a

To turn Call Forward Busy (Variable Number) ON.

OH * 24 DN # RH

 

 

 

b

To turn Call Forward Busy (Variable Number) OFF.

OH # 24 # RH

 

 

 

c

To check if Call Forward (Variable Number) is ON or

OH * # 24 # RSP RH

 

OFF.

 

 

 

 

5.2.5.3 Call Forward No Answer

Call Forward No Answer or Call Forward No Reply (CFNR) will direct a phone calls to another phone when the call rings unanswered.

a

To turn Call Forward No Answer (Variable Number) ON.

OH * 61 DN # RH

 

 

 

b

To turn Call Forward No Answer (Variable Number)

OH # 61 # RH

 

OFF.

 

 

 

 

c

To check if Call Forward (Variable Number) is ON or

OH * # 61 # RSP RH

 

OFF.

 

 

 

 

5.2.6Multiple Subscriber Number (MSN)

Usually two telephone numbers are automatically assigned to an OnRamp service. Before an MSN number is entered into the AT command registers on the ATA, phoning any subscribed number from another phone service will make an attached phone ring. It is possible to have up to eight phone numbers on a single OnRamp service by requesting them from Telstra. The ATA picks up all phone calls unless a specific number is set up for MSN in the ATA for exclusive pick up. Exclusive pick up would be used when the ATA is meant to respond to calls on a different phone number to another device on the same OnRamp service.

Version 1.1

Telstra Corporation Limited

Page 27/29

ACN 051 775 556

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Version Copyright 1999 Telstra Corporation Limited Table of Contents 24 Serial Port ‘AT’ Commands Description 3.1 Application IntroductionDefinitions Package ContentsPort Functions Back PanelDisplay Interpretation Top Panel Seven Segment DisplayConnect the Eftpos terminal to ATA ATA Activation InstructionsPrepare position Connect ATA to NT1Observe D-Channel X.25 Call Progress For the First Call Power-up the ATAAdjust the Display Orientation of the ATA Select the Required TEI NumberObserve for Configuration File Errors Observe the Software DownloadObserve for Failure to Connect Replace the ATA if Faulty on Arrival Observe that the ATA is ready and record the service detailsClick on Control Panel Point-to-Point Protocol PPP InstallationTick Don’t detect my modem I will select from list Installing Dial-Up Network Open Dial-Up Networking Double click on Make New Connection Configuring Dial-Up Networking DUN17 V.120 Setup Connect the Eftpos terminalEnd to end test ATA Maintenance Warranty ATA out of Warranty with Telstra Service Assurance Introduction ‘AT’ CommandsRegister Description Register settingsPots Telephone Supplementary Features 5.1 Introduction RSP Abbreviations used in the Pots feature descriptionsTelephone Port Pots Features Call Waiting CWMalicious Call Identification Mcid / MCT Call Line Presentation Clip Multiple Subscriber Number MSN Call ForwardOH DT #1# telephone number # RH
Top Page Image Contents