Telstrat Argent manual Top Panel Seven Segment Display, Display Interpretation

Page 8

Argent Terminal Adaptor - User Guide

3.5 Top Panel Seven Segment Display

The Seven-Segment display consists of lighted segments to display numbers 0-9 plus a dot. This shows the startup state of the ATA and on-going status of the EFTPOS connection. Displays do not relate to calls on the POTS port or the V.24 serial port (except for EFTPOS).

When starting up the ATA, the Seven-Segment display lights up and moves through a sequence of patterns and numbers. The numbers displayed are steady when the call is progressing and the configuration downloading normally on the D-channel during startup. The display flashes a number continuously if call progress encounters an error condition during startup.

Table 3 provides a list of “startup status codes” that the ATA displays in order of sequence when the power is being applied, the call is being set up, and the configuration is being downloaded by the Argent Network Management System (NMS).

Table 4 provides a list of “fault codes” displayed when a fault occurs.

Display

Interpretation

Building Bars

Program decompressing into memory

Steady 1

Power-on test executing. Dot will pulse on/off.

Steady 2

D-channel interface active for EFTPOS

Steady 3

Pre-Configuration in progress, learning identity.

Steady 4

Remote management in progress, configuration.

Steady 5

Software download in progress

Steady 6

Reserved

Steady 7

Reserved

Steady 8

Reserved

Steady 9

Reserved

Steady 0

Reserved

Steady dot

Normal Operation (no fault)

Table 3: ATA Seven Segment Display Start-up Status Codes

Display

 

Interpretation

Flashing 1

 

Power up self test fails

Flashing 2

 

ISDN connection down

Flashing 3

 

No carrier on EFTPOS modem port

Flashing 4

 

Data overrun/underrun on Serial V.24 port

Flashing 5

 

No stations responding to polls on EFTPOS port

Flashing 6

 

Last call attempt failed, D-Channel. (X.25 fault or

 

 

Argent server or NMS unavailable.)

Flashing 7

 

Not applicable

Flashing 8

 

NMS has no pre-configuration to download

Flashing 9

 

NMS main configuration failure

Flashing 0

 

Not applicable

 

Table 4: ATA Seven Segment Display Fault Codes

Version 1.1

Telstra Corporation Limited

Page 8/29

ACN 051 775 556

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Version Copyright 1999 Telstra Corporation Limited Table of Contents 24 Serial Port ‘AT’ Commands Introduction Description 3.1 ApplicationPackage Contents DefinitionsBack Panel Port FunctionsTop Panel Seven Segment Display Display InterpretationATA Activation Instructions Prepare positionConnect ATA to NT1 Connect the Eftpos terminal to ATAPower-up the ATA Adjust the Display Orientation of the ATASelect the Required TEI Number Observe D-Channel X.25 Call Progress For the First CallObserve for Failure to Connect Observe for Configuration File ErrorsObserve the Software Download Observe that the ATA is ready and record the service details Replace the ATA if Faulty on ArrivalPoint-to-Point Protocol PPP Installation Click on Control PanelTick Don’t detect my modem I will select from list Installing Dial-Up Network Configuring Dial-Up Networking DUN Open Dial-Up Networking Double click on Make New ConnectionEnd to end test 17 V.120 SetupConnect the Eftpos terminal ATA Maintenance Warranty ATA out of Warranty with Telstra Service Assurance ‘AT’ Commands IntroductionRegister settings Register DescriptionPots Telephone Supplementary Features 5.1 Introduction Abbreviations used in the Pots feature descriptions RSPMalicious Call Identification Mcid / MCT Telephone Port Pots FeaturesCall Waiting CW Call Line Presentation Clip Call Forward Multiple Subscriber Number MSNOH DT #1# telephone number # RH
Top Page Image Contents