Savin 4018d, 4015 manual Introduction

Page 2

Introduction

This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine.

Important

Contents of this manual are subject to change without prior notice. In no event will the company be li- able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper- ating the machine.

Notes Some illustrations in this manual might be slightly different from the machine. Certain options might not be available in some countries. For details, please contact your local dealer.

Laser Safety:

CDRH Regulations

This equipment complies with requirements of 21 CFR subchapter J for class 1 laser products. This equipment contains a 5 milliwatt, 760-800 nanometer wavelength, GaAlAs laser diode. This equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes of oper- ation and maintenance.

Warning:

Use of controls or adjustment or performance of procedures other than those specified in this manual might result in hazardous radiation exposure.

Notes:

The model names of the machines do not appear in the following pages. Check the type of your ma- chine before reading this manual. (For details, see P.7 “Machine Types”.)

•Type 1: 4015/DSm615/LD115/Aficio 2015

•Type 2: 4018/DSm618/LD118/Aficio 2018

•Type 3: 4018d/DSm618d/LD118d/Aficio 2018D

Certain types might not be available in some countries. For details, please contact your local dealer. Two kinds of size notation are employed in this manual. With this machine refer to the inch version. For good copy quality, the supplier recommends that you use genuine toner from the supplier.

The supplier shall not be responsible for any damage or expense that might result from the use of parts other than genuine parts from the supplier with your office products.

Power Source 120V, 60Hz, 12A or more

Please be sure to connect the power cord to a power source as above. For details about power source, see P.59 “Power Connection”.

Image 2

Contents Copy Reference Introduction Manuals for This Machine Other manuals Manuals for DeskTopBinder V2 LiteManuals for ScanRouter V2 Lite Table of Contents Dos and Donts Where to Put Your Machine Accessing User Tools Copier FeaturesSettings You Can Change with User Tools If Your Machine Does Not Operate As You WantSpecifications Combination Chart Supplementary InformationPage Page Remarque concernant les utilisateurs au Canada Avertissement Names of Major Options How to Read This ManualSymbols Safety Information Safety During OperationPage AAI029S Machine Types Copier only Options fully installedControl Panel Sort key Cancel keyCombine/Series key Lighter and DarkerInitial copy display Reading the Display and Using KeysDisplay Scroll keys Turning On the Power Turning On the PowerTurning On the Main Power Operation switch right side of the control panelTurning Off the Power Turning Off the Main PowerAuto Off/ Low Power Saving EnergyMetric version Sizes and Weights of Recommended OriginalsOriginals Inch versionSizes Detectable with Auto Paper Select ADF or Ardf Missing Image AreaExposure glass Sizes difficult to detectPlacing Originals on the Exposure Glass Placing OriginalsOriginal Orientation Ardf Limit mark Document guidePlacing custom size originals To stop the machine during a multi- copy run Basic ProcedureTo switch between pages or select functions To clear an entered valuePush up the paper guide release lever Copying from the Bypass TrayOpen the bypass tray Paper guide release leverHorizontal size Vertical size Extender Paper guides Select Paper Size using U or T, and then press the OK keySelect Regular Size using U or T, and then press the OK key Pull down the paper guide release the lever step BFeeds Select Paper Size using U orSelect Custom Size using U or T, and then press the OK key Then press the OKSelect Thick Paper using U or T, and then press the OK key Copier Functions Adjusting Image DensitySelecting Original Type Setting Selecting Copy PaperMake sure Auto Paper Select is se- lected Preset Reduce/EnlargeSelect the paper tray or bypass tray using U or T Press Reduce or Enlarge ZoomBase Point Enter the ratio Adjust the ratio using U or TAuto Reduce/Enlarge Press the OK keySort SortRotate Sort Sided → 2 Sided Optional Ardf is required Duplex Type 3 onlySided → 2 Sided Select Sort or Rotate Sort, and then press the OK keyOriginal orientation and completed copies Press the Duplex keySided 4 Pages → Combine 1 Side One-Sided CombineSided 2 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is requiredSided 2 Pages → Combine 1 Side Optional Ardf is requiredPosition of combine Orientation of the original and imageSided 4 Pages → Combine 2 Side Optional Ardf is required Two-Sided Combine Type 3 onlySided 8 Pages → Combine 2 Side Sided 4 Pages → Combine 2 SideTop or Top to Bottom using U or Then press the OK keyBook→1 Sided Series CopiesSided→1 Sided Optional Ardf is required Press the Combine/Series keySelect the paper tray using U or T Place your original, and then press the Start keyWhen a Message Is Displayed If Your Machine Does Not Operate As You WantProblem Causes Solutions If You Cannot Make Clear CopiesEdit If You Cannot Make Copies As You WantBasic CombineWhen Memory Is Full Duplex Type 3 onlyPush the paper tray in, until it stops Loading PaperLoading Paper Orientation-Fixed Paper or Two-Sided Paper Original OrientationLoaded paper orientation For MFP Toner Storage Adding TonerHandling Toner Used TonerRemoving Toner Inserting Toner Troubleshooting Press the User Tools/Counter key Accessing User Tools Copier FeaturesChanging Default Settings Quitting User Tools Change is made, and the ma- chine is ready to copyOriginal Type Setting Settings You Can Change with User ToolsAuto Tray Switching APS/ Auto R/E PriorityMax. Number of Sets Duplex Mode PriorityOrientation Original Count DisplayDuplex Margin Preset R/E PriorityLetterhead Setting Rotate SortUser Tools Copier Features Remarks Dos and DontsOptimum environmental conditions Where to Put Your MachineMachine Environment Environments to avoidPower Connection MovingAccess to the Machine Cleaning the ADF or Ardf Cleaning the Exposure GlassCleaning the Exposure Glass Cover Cleaning the machineRemarks Specifications Combination ChartBypass Tray Copy Preset Enlarge/ReduceSupplementary Information Zoom Sort, Rotate SortDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607