Savin 4015, 4018d manual Moving, Power Connection

Page 67

KirC2_ENcopyF_FM.book Page 59 Monday, September 22, 2003 11:36 AM

Where to Put Your Machine

Moving

RCAUTION:

•Unplug the power cord from the wall outlet before you move the machine. While moving the ma- chine, you should take care that the power cord will not be dam- aged under the machine.

RCAUTION:

•Before moving the machine, be sure to pull all four handles fully out. If not, an injury might occur. After moving the machine, return the four handles to their original positions.

•When the optional paper tray unit is installed, do not push the up- per part of the main unit horizon- tally. An injury might occur if the paper tray unit becomes de- tached from the main unit.

Important

❒Be careful when moving the ma- chine. Take the following precau- tions:

•Turn off the main power. See p.13 “Turning Off the Main Power”.

•Unplug the power cord from the wall outlet. When you pull out the plug from the socket, grip the plug to avoid damag- ing the cord, thereby reducing the risk of fire or electric shock.

•Close all covers and trays, in- cluding the front cover and by- pass tray.

❒Do not take off the holding stand.

❒Protect the machine from strong shocks. Impact can damage the memory.

Power Connection

RWARNING:

•Connect the machine only to the power source described on the inside front cover of this manual. Connect the power cord directly into a wall outlet and do not use an extension cord.

•Do not damage, break or make any modifications to the power cord. Do not place heavy ob- jects on it. Do not pull it hard nor bend it more than neces- sary. These actions could cause an electric shock or fire.

RCAUTION:

•Unplug the power cord from the wall outlet before you move the machine. While moving the ma- chine, you should take care that the power cord will not be dam- aged under the machine.

RCAUTION:

•When you disconnect the power plug from the wall outlet, always pull the plug (not the cable).

•When the main power switch is in the stand-by position, the optional anti-condensation heaters are on. In an emergency, unplug the ma- chine's power cord.

•When you unplug the power cord, the anti-condensation heaters turn off.

•Make sure the plug is inserted firmly in the wall outlet.

•Voltage must not fluctuate by more than 10%.

•The wall outlet shall be installed near the machine and shall be eas- ily accessible.

5

59

Page 66 Page 68
Image 67
Page 66 Page 68
Contents Copy Reference Introduction Manuals for This Machine Manuals for ScanRouter V2 Lite Manuals for DeskTopBinder V2 LiteOther manuals Table of Contents If Your Machine Does Not Operate As You Want Accessing User Tools Copier FeaturesSettings You Can Change with User Tools Dos and Donts Where to Put Your MachineCombination Chart Supplementary Information SpecificationsPage Page Remarque concernant les utilisateurs au Canada Avertissement Symbols How to Read This ManualNames of Major Options Safety During Operation Safety InformationPage AAI029S Machine Types Control Panel Options fully installedCopier only Lighter and Darker Cancel keyCombine/Series key Sort keyDisplay Reading the Display and Using KeysInitial copy display Scroll keys Operation switch right side of the control panel Turning On the PowerTurning On the Main Power Turning On the PowerTurning Off the Main Power Turning Off the PowerSaving Energy Auto Off/ Low PowerInch version Sizes and Weights of Recommended OriginalsOriginals Metric versionSizes Detectable with Auto Paper Select Sizes difficult to detect Missing Image AreaExposure glass ADF or ArdfOriginal Orientation Placing OriginalsPlacing Originals on the Exposure Glass Limit mark Document guide ArdfPlacing custom size originals To clear an entered value Basic ProcedureTo switch between pages or select functions To stop the machine during a multi- copy runPaper guide release lever Copying from the Bypass TrayOpen the bypass tray Push up the paper guide release leverPull down the paper guide release the lever step B Select Paper Size using U or T, and then press the OK keySelect Regular Size using U or T, and then press the OK key Horizontal size Vertical size Extender Paper guidesThen press the OK Select Paper Size using U orSelect Custom Size using U or T, and then press the OK key FeedsSelect Thick Paper using U or T, and then press the OK key Selecting Copy Paper Adjusting Image DensitySelecting Original Type Setting Copier FunctionsSelect the paper tray or bypass tray using U or T Preset Reduce/EnlargeMake sure Auto Paper Select is se- lected Base Point ZoomPress Reduce or Enlarge Press the OK key Adjust the ratio using U or TAuto Reduce/Enlarge Enter the ratioRotate Sort SortSort Select Sort or Rotate Sort, and then press the OK key Duplex Type 3 onlySided → 2 Sided Sided → 2 Sided Optional Ardf is requiredPress the Duplex key Original orientation and completed copiesSided 1 Page → Combine 1 Side Optional Ardf is required One-Sided CombineSided 2 Pages → Combine 1 Side Sided 4 Pages → Combine 1 SideOrientation of the original and image Optional Ardf is requiredPosition of combine Sided 2 Pages → Combine 1 SideSided 4 Pages → Combine 2 Side Two-Sided Combine Type 3 onlySided 8 Pages → Combine 2 Side Sided 4 Pages → Combine 2 Side Optional Ardf is requiredThen press the OK key Top or Top to Bottom using U orPress the Combine/Series key Series CopiesSided→1 Sided Optional Ardf is required Book→1 SidedPlace your original, and then press the Start key Select the paper tray using U or TIf Your Machine Does Not Operate As You Want When a Message Is DisplayedIf You Cannot Make Clear Copies Problem Causes SolutionsCombine If You Cannot Make Copies As You WantBasic EditDuplex Type 3 only When Memory Is FullLoading Paper Loading PaperPush the paper tray in, until it stops Original Orientation Orientation-Fixed Paper or Two-Sided PaperLoaded paper orientation For MFP Used Toner Adding TonerHandling Toner Toner StorageRemoving Toner Inserting Toner Troubleshooting Changing Default Settings Accessing User Tools Copier FeaturesPress the User Tools/Counter key Change is made, and the ma- chine is ready to copy Quitting User ToolsAPS/ Auto R/E Priority Settings You Can Change with User ToolsAuto Tray Switching Original Type SettingOriginal Count Display Duplex Mode PriorityOrientation Max. Number of SetsRotate Sort Preset R/E PriorityLetterhead Setting Duplex MarginUser Tools Copier Features Dos and Donts RemarksEnvironments to avoid Where to Put Your MachineMachine Environment Optimum environmental conditionsMoving Power ConnectionAccess to the Machine Cleaning the machine Cleaning the Exposure GlassCleaning the Exposure Glass Cover Cleaning the ADF or ArdfRemarks Combination Chart SpecificationsSupplementary Information Preset Enlarge/ReduceBypass Tray Copy Sort, Rotate Sort ZoomDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607
Top Page Image Contents