Savin 4015, 4018d manual Placing custom size originals

Page 28

KirC2_ENcopyF_FM.book Page 20 Monday, September 22, 2003 11:36 AM

Placing Originals

1

Placing custom size originals

When placing custom size originals in the ADF, or ARDF, specify the size of the originals.

Note

Paper that has a vertical length of 105–297 mm (4.2"–11.6") and a hor- izontal length of 128–1260 mm (5.1"–49.6") can be placed with this function.

A Select the paper tray or bypass tray using {U} or {T}, and then press the {#} key.

The “Accepted” message appears with your set original size.

When the custom size originals settings are registered, appears on the top of copy display.

20

B Enter the horizontal size of the original using the number keys, and then press the {OK} key.

Note

If you make a mistake, press the {Clear/Stop} key, and then enter the value again.

C Enter the vertical size of the origi- nal using the number keys, and then press the {OK} key.

Image 28
Contents Copy Reference Introduction Manuals for This Machine Manuals for ScanRouter V2 Lite Manuals for DeskTopBinder V2 LiteOther manuals Table of Contents Accessing User Tools Copier Features Settings You Can Change with User ToolsDos and Donts Where to Put Your Machine If Your Machine Does Not Operate As You WantSpecifications Combination Chart Supplementary InformationPage Page Remarque concernant les utilisateurs au Canada Avertissement Symbols How to Read This ManualNames of Major Options Safety Information Safety During OperationPage AAI029S Machine Types Control Panel Options fully installedCopier only Cancel key Combine/Series keySort key Lighter and DarkerDisplay Reading the Display and Using KeysInitial copy display Scroll keys Turning On the Power Turning On the Main PowerTurning On the Power Operation switch right side of the control panelTurning Off the Power Turning Off the Main PowerAuto Off/ Low Power Saving EnergySizes and Weights of Recommended Originals OriginalsMetric version Inch versionSizes Detectable with Auto Paper Select Missing Image Area Exposure glassADF or Ardf Sizes difficult to detectOriginal Orientation Placing OriginalsPlacing Originals on the Exposure Glass Ardf Limit mark Document guidePlacing custom size originals Basic Procedure To switch between pages or select functionsTo stop the machine during a multi- copy run To clear an entered valueCopying from the Bypass Tray Open the bypass trayPush up the paper guide release lever Paper guide release leverSelect Paper Size using U or T, and then press the OK key Select Regular Size using U or T, and then press the OK keyHorizontal size Vertical size Extender Paper guides Pull down the paper guide release the lever step BSelect Paper Size using U or Select Custom Size using U or T, and then press the OK keyFeeds Then press the OKSelect Thick Paper using U or T, and then press the OK key Adjusting Image Density Selecting Original Type SettingCopier Functions Selecting Copy PaperSelect the paper tray or bypass tray using U or T Preset Reduce/EnlargeMake sure Auto Paper Select is se- lected Base Point ZoomPress Reduce or Enlarge Adjust the ratio using U or T Auto Reduce/EnlargeEnter the ratio Press the OK keyRotate Sort SortSort Duplex Type 3 only Sided → 2 SidedSided → 2 Sided Optional Ardf is required Select Sort or Rotate Sort, and then press the OK keyOriginal orientation and completed copies Press the Duplex keyOne-Sided Combine Sided 2 Pages → Combine 1 SideSided 4 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is requiredOptional Ardf is required Position of combineSided 2 Pages → Combine 1 Side Orientation of the original and imageTwo-Sided Combine Type 3 only Sided 8 Pages → Combine 2 SideSided 4 Pages → Combine 2 Side Optional Ardf is required Sided 4 Pages → Combine 2 SideTop or Top to Bottom using U or Then press the OK keySeries Copies Sided→1 Sided Optional Ardf is requiredBook→1 Sided Press the Combine/Series keySelect the paper tray using U or T Place your original, and then press the Start keyWhen a Message Is Displayed If Your Machine Does Not Operate As You WantProblem Causes Solutions If You Cannot Make Clear CopiesIf You Cannot Make Copies As You Want BasicEdit CombineWhen Memory Is Full Duplex Type 3 onlyLoading Paper Loading PaperPush the paper tray in, until it stops Orientation-Fixed Paper or Two-Sided Paper Original OrientationLoaded paper orientation For MFP Adding Toner Handling TonerToner Storage Used TonerRemoving Toner Inserting Toner Troubleshooting Changing Default Settings Accessing User Tools Copier FeaturesPress the User Tools/Counter key Quitting User Tools Change is made, and the ma- chine is ready to copySettings You Can Change with User Tools Auto Tray SwitchingOriginal Type Setting APS/ Auto R/E PriorityDuplex Mode Priority OrientationMax. Number of Sets Original Count DisplayPreset R/E Priority Letterhead SettingDuplex Margin Rotate SortUser Tools Copier Features Remarks Dos and DontsWhere to Put Your Machine Machine EnvironmentOptimum environmental conditions Environments to avoidPower Connection MovingAccess to the Machine Cleaning the Exposure Glass Cleaning the Exposure Glass CoverCleaning the ADF or Ardf Cleaning the machineRemarks Specifications Combination ChartSupplementary Information Preset Enlarge/ReduceBypass Tray Copy Zoom Sort, Rotate SortDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607