Savin 4018d, 4015 manual Zoom, Base Point, Press Reduce or Enlarge

Page 36

KirC2_ENcopyF_FM.book Page 28 Monday, September 22, 2003 11:36 AM

Copying

❖Base Point

The base point of Reduce/Enlarge differs depending on how the orig- inal is scanned. When the original is placed on the exposure glass, the upper left corner is the base point.

When placed in the ADF or ARDF, the bottom left corner is the base

2 point.

GCKA031e

C Select a ratio using {U} or {T}, and then press the {OK} key.

The “Accepted” message appears.

D Place your originals, and then press the {Start} key.

Zoom

You can change the reproduction ra- tio in increments of 1%.

1.Base point when placing on the exposure glass.

2.Base point when placing in the ADF or ARDF.

Reference

Related default settings

p.54 “Reproduction Ratio”

p.55 “Preset R/E Priority”

A Press [R/E].

B Press [Reduce] or [Enlarge].

Note

❒You can also select a preset ratio close to the desired ratio using [Re- duce] or [Enlarge], and then adjust the ratio using {U} or {T}.

A Press [R/E].

B Press [Zoom].

Image 36

Contents Copy Reference Introduction Manuals for This Machine Manuals for DeskTopBinder V2 Lite Manuals for ScanRouter V2 LiteOther manuals Table of Contents Accessing User Tools Copier Features Settings You Can Change with User ToolsDos and Donts Where to Put Your Machine If Your Machine Does Not Operate As You WantSpecifications Combination Chart Supplementary InformationPage Page Remarque concernant les utilisateurs au Canada Avertissement How to Read This Manual SymbolsNames of Major Options Safety Information Safety During OperationPage AAI029S Machine Types Options fully installed Control PanelCopier only Cancel key Combine/Series keySort key Lighter and DarkerReading the Display and Using Keys DisplayInitial copy display Scroll keys Turning On the Power Turning On the Main PowerTurning On the Power Operation switch right side of the control panelTurning Off the Power Turning Off the Main PowerAuto Off/ Low Power Saving EnergySizes and Weights of Recommended Originals OriginalsMetric version Inch versionSizes Detectable with Auto Paper Select Missing Image Area Exposure glassADF or Ardf Sizes difficult to detectPlacing Originals Original OrientationPlacing Originals on the Exposure Glass Ardf Limit mark Document guidePlacing custom size originals Basic Procedure To switch between pages or select functionsTo stop the machine during a multi- copy run To clear an entered valueCopying from the Bypass Tray Open the bypass trayPush up the paper guide release lever Paper guide release leverSelect Paper Size using U or T, and then press the OK key Select Regular Size using U or T, and then press the OK keyHorizontal size Vertical size Extender Paper guides Pull down the paper guide release the lever step BSelect Paper Size using U or Select Custom Size using U or T, and then press the OK keyFeeds Then press the OK Select Thick Paper using U or T, and then press the OK key Adjusting Image Density Selecting Original Type SettingCopier Functions Selecting Copy PaperPreset Reduce/Enlarge Select the paper tray or bypass tray using U or TMake sure Auto Paper Select is se- lected Zoom Base PointPress Reduce or Enlarge Adjust the ratio using U or T Auto Reduce/EnlargeEnter the ratio Press the OK keySort Rotate SortSort Duplex Type 3 only Sided → 2 SidedSided → 2 Sided Optional Ardf is required Select Sort or Rotate Sort, and then press the OK keyOriginal orientation and completed copies Press the Duplex keyOne-Sided Combine Sided 2 Pages → Combine 1 SideSided 4 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is requiredOptional Ardf is required Position of combineSided 2 Pages → Combine 1 Side Orientation of the original and imageTwo-Sided Combine Type 3 only Sided 8 Pages → Combine 2 SideSided 4 Pages → Combine 2 Side Optional Ardf is required Sided 4 Pages → Combine 2 SideTop or Top to Bottom using U or Then press the OK keySeries Copies Sided→1 Sided Optional Ardf is requiredBook→1 Sided Press the Combine/Series keySelect the paper tray using U or T Place your original, and then press the Start keyWhen a Message Is Displayed If Your Machine Does Not Operate As You WantProblem Causes Solutions If You Cannot Make Clear CopiesIf You Cannot Make Copies As You Want BasicEdit CombineWhen Memory Is Full Duplex Type 3 onlyLoading Paper Loading PaperPush the paper tray in, until it stops Orientation-Fixed Paper or Two-Sided Paper Original OrientationLoaded paper orientation For MFP Adding Toner Handling TonerToner Storage Used TonerRemoving Toner Inserting Toner Troubleshooting Accessing User Tools Copier Features Changing Default SettingsPress the User Tools/Counter key Quitting User Tools Change is made, and the ma- chine is ready to copySettings You Can Change with User Tools Auto Tray SwitchingOriginal Type Setting APS/ Auto R/E PriorityDuplex Mode Priority OrientationMax. Number of Sets Original Count DisplayPreset R/E Priority Letterhead SettingDuplex Margin Rotate SortUser Tools Copier Features Remarks Dos and DontsWhere to Put Your Machine Machine EnvironmentOptimum environmental conditions Environments to avoidPower Connection MovingAccess to the Machine Cleaning the Exposure Glass Cleaning the Exposure Glass CoverCleaning the ADF or Ardf Cleaning the machineRemarks Specifications Combination ChartPreset Enlarge/Reduce Supplementary InformationBypass Tray Copy Zoom Sort, Rotate SortDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607