Savin 4018d, 4015 manual Accessing User Tools Copier Features, Changing Default Settings

Page 59

KirC2_ENcopyF_FM.book Page 51 Monday, September 22, 2003 11:36 AM

4. User Tools (Copier Features)

Accessing User Tools (Copier Features)

This section is for key operators in charge of this machine. Key operators can change or make default settings.

Note

❒Be sure to quit User Tools and re- turn to the initial copy display when all settings are complete. This section describes system set- tings for the copier function.

❒Selected settings are highlighted.

❒Any changes made with User Tools remain in effect even if the main power switch or operation switch is turned off, or the {Clear Modes} key is pressed.

Reference

For details, see "User Tools (Sys- tem Settings)", General Settings Guide.

Changing Default Settings

Note

❒If a key operator code is set, the key operator code input display appears before you can change the default settings. For details about access codes, see “Key Operator Tools”, General Settings Guide.

A Press the {User Tools/Counter} key.

		User Tools/		Clear
		Counter		Modes
	Hook Dial			Clear/Stop
				Clear/Stop
			ABC	DEF
	Pause/	GHI	JKL	MNO
	Redial	GHI	JKL	MNO
	Redial			Start
				Start
		PRS	TUV	WXY
				AAH027S

B Select [Copier Features] using {U} or {T}, and then press the {OK} key.

C Select the menu using {U} or {T}, and then press the {OK} key.

D Change settings by following in- structions on the display, and then press the {OK} key.

The “Programmed” message ap- pears.

51

Image 59

Contents Copy Reference Introduction Manuals for This Machine Other manuals Manuals for DeskTopBinder V2 LiteManuals for ScanRouter V2 Lite Table of Contents If Your Machine Does Not Operate As You Want Accessing User Tools Copier FeaturesSettings You Can Change with User Tools Dos and Donts Where to Put Your MachineCombination Chart Supplementary Information SpecificationsPage Page Remarque concernant les utilisateurs au Canada Avertissement Names of Major Options How to Read This ManualSymbols Safety During Operation Safety InformationPage AAI029S Machine Types Copier only Options fully installedControl Panel Lighter and Darker Cancel keyCombine/Series key Sort keyInitial copy display Reading the Display and Using KeysDisplay Scroll keys Operation switch right side of the control panel Turning On the PowerTurning On the Main Power Turning On the PowerTurning Off the Main Power Turning Off the PowerSaving Energy Auto Off/ Low PowerInch version Sizes and Weights of Recommended OriginalsOriginals Metric versionSizes Detectable with Auto Paper Select Sizes difficult to detect Missing Image AreaExposure glass ADF or ArdfPlacing Originals on the Exposure Glass Placing OriginalsOriginal Orientation Limit mark Document guide ArdfPlacing custom size originals To clear an entered value Basic ProcedureTo switch between pages or select functions To stop the machine during a multi- copy runPaper guide release lever Copying from the Bypass TrayOpen the bypass tray Push up the paper guide release leverPull down the paper guide release the lever step B Select Paper Size using U or T, and then press the OK keySelect Regular Size using U or T, and then press the OK key Horizontal size Vertical size Extender Paper guidesThen press the OK Select Paper Size using U orSelect Custom Size using U or T, and then press the OK key FeedsSelect Thick Paper using U or T, and then press the OK key Selecting Copy Paper Adjusting Image DensitySelecting Original Type Setting Copier FunctionsMake sure Auto Paper Select is se- lected Preset Reduce/EnlargeSelect the paper tray or bypass tray using U or T Press Reduce or Enlarge ZoomBase Point Press the OK key Adjust the ratio using U or TAuto Reduce/Enlarge Enter the ratioSort SortRotate Sort Select Sort or Rotate Sort, and then press the OK key Duplex Type 3 onlySided → 2 Sided Sided → 2 Sided Optional Ardf is requiredPress the Duplex key Original orientation and completed copiesSided 1 Page → Combine 1 Side Optional Ardf is required One-Sided CombineSided 2 Pages → Combine 1 Side Sided 4 Pages → Combine 1 SideOrientation of the original and image Optional Ardf is requiredPosition of combine Sided 2 Pages → Combine 1 SideSided 4 Pages → Combine 2 Side Two-Sided Combine Type 3 onlySided 8 Pages → Combine 2 Side Sided 4 Pages → Combine 2 Side Optional Ardf is requiredThen press the OK key Top or Top to Bottom using U orPress the Combine/Series key Series CopiesSided→1 Sided Optional Ardf is required Book→1 SidedPlace your original, and then press the Start key Select the paper tray using U or TIf Your Machine Does Not Operate As You Want When a Message Is DisplayedIf You Cannot Make Clear Copies Problem Causes SolutionsCombine If You Cannot Make Copies As You WantBasic EditDuplex Type 3 only When Memory Is FullPush the paper tray in, until it stops Loading PaperLoading Paper Original Orientation Orientation-Fixed Paper or Two-Sided PaperLoaded paper orientation For MFP Used Toner Adding TonerHandling Toner Toner Storage Removing Toner Inserting Toner Troubleshooting Press the User Tools/Counter key Accessing User Tools Copier FeaturesChanging Default Settings Change is made, and the ma- chine is ready to copy Quitting User ToolsAPS/ Auto R/E Priority Settings You Can Change with User ToolsAuto Tray Switching Original Type SettingOriginal Count Display Duplex Mode PriorityOrientation Max. Number of SetsRotate Sort Preset R/E PriorityLetterhead Setting Duplex MarginUser Tools Copier Features Dos and Donts RemarksEnvironments to avoid Where to Put Your MachineMachine Environment Optimum environmental conditionsMoving Power ConnectionAccess to the Machine Cleaning the machine Cleaning the Exposure GlassCleaning the Exposure Glass Cover Cleaning the ADF or ArdfRemarks Combination Chart SpecificationsBypass Tray Copy Preset Enlarge/ReduceSupplementary Information Sort, Rotate Sort ZoomDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607