Savin 4015, 4018d manual Missing Image Area, Exposure glass, ADF or Ardf, Sizes difficult to detect

Page 25

KirC2_ENcopyF_FM.book Page 17 Monday, September 22, 2003 11:36 AM

❖Exposure glass

Positioning
mark	Horizontal size
	Horizontal size
Vertical	Maximum scanning area
	Maximum scanning area
size	A3	(297x420mm)
size	11"x17"		(279x432mm)

❖ADF or ARDF

Maximum scanning area

Note

Originals

1

❒When you copy custom size originals, make sure you specify the size of the originals. If not, the image may not be copied properly. See p.20 “Placing cus- tom size originals”.

Sizes difficult to detect

It is difficult for the machine to detect the sizes of the following originals, so se- lect the paper size manually.

•Originals with indexes, tags, or other projecting parts

•Transparent originals such as OHP transparencies or translucent paper

•Dark originals with lots of text and drawings

•Originals partially consisting of a solid image

•Originals that have solid images around their edges

Missing Image Area

Even if you place originals in the ADF or ARDF, or on the exposure glass cor- rectly, 4 mm (0.2”) margins on all four sides might not be copied.

17

Image 25

Contents Copy Reference Introduction Manuals for This Machine Manuals for ScanRouter V2 Lite Manuals for DeskTopBinder V2 LiteOther manuals Table of Contents Settings You Can Change with User Tools Accessing User Tools Copier FeaturesDos and Donts Where to Put Your Machine If Your Machine Does Not Operate As You WantCombination Chart Supplementary Information SpecificationsPage Page Remarque concernant les utilisateurs au Canada Avertissement Symbols How to Read This ManualNames of Major Options Safety During Operation Safety InformationPage AAI029S Machine Types Control Panel Options fully installedCopier only Combine/Series key Cancel keySort key Lighter and DarkerDisplay Reading the Display and Using KeysInitial copy display Scroll keys Turning On the Main Power Turning On the PowerTurning On the Power Operation switch right side of the control panelTurning Off the Main Power Turning Off the PowerSaving Energy Auto Off/ Low PowerOriginals Sizes and Weights of Recommended OriginalsMetric version Inch versionSizes Detectable with Auto Paper Select Exposure glass Missing Image AreaADF or Ardf Sizes difficult to detectOriginal Orientation Placing OriginalsPlacing Originals on the Exposure Glass Limit mark Document guide ArdfPlacing custom size originals To switch between pages or select functions Basic ProcedureTo stop the machine during a multi- copy run To clear an entered valueOpen the bypass tray Copying from the Bypass TrayPush up the paper guide release lever Paper guide release leverSelect Regular Size using U or T, and then press the OK key Select Paper Size using U or T, and then press the OK keyHorizontal size Vertical size Extender Paper guides Pull down the paper guide release the lever step BSelect Custom Size using U or T, and then press the OK key Select Paper Size using U orFeeds Then press the OKSelect Thick Paper using U or T, and then press the OK key Selecting Original Type Setting Adjusting Image DensityCopier Functions Selecting Copy PaperSelect the paper tray or bypass tray using U or T Preset Reduce/EnlargeMake sure Auto Paper Select is se- lected Base Point ZoomPress Reduce or Enlarge Auto Reduce/Enlarge Adjust the ratio using U or TEnter the ratio Press the OK keyRotate Sort SortSort Sided → 2 Sided Duplex Type 3 onlySided → 2 Sided Optional Ardf is required Select Sort or Rotate Sort, and then press the OK keyPress the Duplex key Original orientation and completed copiesSided 2 Pages → Combine 1 Side One-Sided CombineSided 4 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is requiredPosition of combine Optional Ardf is requiredSided 2 Pages → Combine 1 Side Orientation of the original and imageSided 8 Pages → Combine 2 Side Two-Sided Combine Type 3 onlySided 4 Pages → Combine 2 Side Optional Ardf is required Sided 4 Pages → Combine 2 SideThen press the OK key Top or Top to Bottom using U orSided→1 Sided Optional Ardf is required Series CopiesBook→1 Sided Press the Combine/Series keyPlace your original, and then press the Start key Select the paper tray using U or TIf Your Machine Does Not Operate As You Want When a Message Is DisplayedIf You Cannot Make Clear Copies Problem Causes SolutionsBasic If You Cannot Make Copies As You WantEdit CombineDuplex Type 3 only When Memory Is FullLoading Paper Loading PaperPush the paper tray in, until it stops Original Orientation Orientation-Fixed Paper or Two-Sided PaperLoaded paper orientation For MFP Handling Toner Adding TonerToner Storage Used TonerRemoving Toner Inserting Toner Troubleshooting Changing Default Settings Accessing User Tools Copier FeaturesPress the User Tools/Counter key Change is made, and the ma- chine is ready to copy Quitting User ToolsAuto Tray Switching Settings You Can Change with User ToolsOriginal Type Setting APS/ Auto R/E PriorityOrientation Duplex Mode PriorityMax. Number of Sets Original Count DisplayLetterhead Setting Preset R/E PriorityDuplex Margin Rotate SortUser Tools Copier Features Dos and Donts RemarksMachine Environment Where to Put Your MachineOptimum environmental conditions Environments to avoidMoving Power ConnectionAccess to the Machine Cleaning the Exposure Glass Cover Cleaning the Exposure GlassCleaning the ADF or Ardf Cleaning the machineRemarks Combination Chart SpecificationsSupplementary Information Preset Enlarge/ReduceBypass Tray Copy Sort, Rotate Sort ZoomDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607