Savin 4015, 4018d manual Saving Energy, Auto Off/ Low Power

Page 22

KirC2_ENcopyF_FM.book Page 14 Monday, September 22, 2003 11:36 AM

Saving Energy

-Auto Off/ Low Power

The machine automatically turns it- self off when the job is finished, after a certain period of time has elapsed. This function is called “Auto Off”.

Note

❒You can change the Auto Off time. See General Settings Guide.

❒The Auto Off Timer function will not operate in the following cases:

•When a warning message ap- pears

•When the service call message appears

•When paper is jammed

•When the cover is open

•When the “Add Toner” mes- sage appears

•When toner is being replen- ished

•When the User Tools screen is displayed

•When fixed warm-up is in progress

•When the facsimile, printer, or other functions are active

•When operations are suspend- ed during printing

•When the On-hook dialing function is in use

•When a receiver is being regis- tered in the Address Book or group dial list

•When the Data In indicator is on or blinking

Image 22

Contents Copy Reference Introduction Manuals for This Machine Manuals for ScanRouter V2 Lite Manuals for DeskTopBinder V2 LiteOther manuals Table of Contents Dos and Donts Where to Put Your Machine Accessing User Tools Copier FeaturesSettings You Can Change with User Tools If Your Machine Does Not Operate As You WantSpecifications Combination Chart Supplementary InformationPage Page Remarque concernant les utilisateurs au Canada Avertissement Symbols How to Read This ManualNames of Major Options Safety Information Safety During OperationPage AAI029S Machine Types Control Panel Options fully installedCopier only Sort key Cancel keyCombine/Series key Lighter and DarkerDisplay Reading the Display and Using KeysInitial copy display Scroll keys Turning On the Power Turning On the PowerTurning On the Main Power Operation switch right side of the control panelTurning Off the Power Turning Off the Main PowerAuto Off/ Low Power Saving EnergyMetric version Sizes and Weights of Recommended OriginalsOriginals Inch versionSizes Detectable with Auto Paper Select ADF or Ardf Missing Image AreaExposure glass Sizes difficult to detectOriginal Orientation Placing OriginalsPlacing Originals on the Exposure Glass Ardf Limit mark Document guidePlacing custom size originals To stop the machine during a multi- copy run Basic ProcedureTo switch between pages or select functions To clear an entered valuePush up the paper guide release lever Copying from the Bypass TrayOpen the bypass tray Paper guide release leverHorizontal size Vertical size Extender Paper guides Select Paper Size using U or T, and then press the OK keySelect Regular Size using U or T, and then press the OK key Pull down the paper guide release the lever step BFeeds Select Paper Size using U orSelect Custom Size using U or T, and then press the OK key Then press the OKSelect Thick Paper using U or T, and then press the OK key Copier Functions Adjusting Image DensitySelecting Original Type Setting Selecting Copy PaperSelect the paper tray or bypass tray using U or T Preset Reduce/EnlargeMake sure Auto Paper Select is se- lected Base Point ZoomPress Reduce or Enlarge Enter the ratio Adjust the ratio using U or TAuto Reduce/Enlarge Press the OK keyRotate Sort SortSort Sided → 2 Sided Optional Ardf is required Duplex Type 3 onlySided → 2 Sided Select Sort or Rotate Sort, and then press the OK keyOriginal orientation and completed copies Press the Duplex keySided 4 Pages → Combine 1 Side One-Sided CombineSided 2 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is requiredSided 2 Pages → Combine 1 Side Optional Ardf is requiredPosition of combine Orientation of the original and imageSided 4 Pages → Combine 2 Side Optional Ardf is required Two-Sided Combine Type 3 onlySided 8 Pages → Combine 2 Side Sided 4 Pages → Combine 2 SideTop or Top to Bottom using U or Then press the OK keyBook→1 Sided Series CopiesSided→1 Sided Optional Ardf is required Press the Combine/Series keySelect the paper tray using U or T Place your original, and then press the Start keyWhen a Message Is Displayed If Your Machine Does Not Operate As You WantProblem Causes Solutions If You Cannot Make Clear CopiesEdit If You Cannot Make Copies As You WantBasic CombineWhen Memory Is Full Duplex Type 3 onlyLoading Paper Loading PaperPush the paper tray in, until it stops Orientation-Fixed Paper or Two-Sided Paper Original OrientationLoaded paper orientation For MFP Toner Storage Adding TonerHandling Toner Used TonerRemoving Toner Inserting Toner Troubleshooting Changing Default Settings Accessing User Tools Copier FeaturesPress the User Tools/Counter key Quitting User Tools Change is made, and the ma- chine is ready to copyOriginal Type Setting Settings You Can Change with User ToolsAuto Tray Switching APS/ Auto R/E PriorityMax. Number of Sets Duplex Mode PriorityOrientation Original Count DisplayDuplex Margin Preset R/E PriorityLetterhead Setting Rotate SortUser Tools Copier Features Remarks Dos and DontsOptimum environmental conditions Where to Put Your MachineMachine Environment Environments to avoidPower Connection MovingAccess to the Machine Cleaning the ADF or Ardf Cleaning the Exposure GlassCleaning the Exposure Glass Cover Cleaning the machineRemarks Specifications Combination ChartSupplementary Information Preset Enlarge/ReduceBypass Tray Copy Zoom Sort, Rotate SortDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607