Savin 4018d, 4015 manual Basic Procedure, To switch between pages or select functions

Page 29

KirC2_ENcopyF_FM.book Page 21 Monday, September 22, 2003 11:36 AM

2. Copying

Basic Procedure

A If the machine has user codes set, enter a user code (up to eight dig- its) using the number keys, and then press the {OK} or {#} key.

The machine is ready to copy.

Reference

For user codes, see “Key Opera- tor Tools”, General Settings Guide.

B Make sure "d Ready" appears on the display.

❖Initial copy display

If any other function is displayed, press the {Copy} key.

C Make sure no previous settings remain.

Note

❒When there are previous set- tings remaining, press the {Clear Modes} key and enter again.

D Place your originals.

Reference

p.18 “Placing Originals”

E Make the necessary settings.

Reference

See the explanations for each function.

F Enter the number of copies using the number keys.

Note

❒The maximum copy quantity that can be set is 99.

G Press the {Start} key.

Copying starts.

Note

❒Copies are delivered face down.

-How to operate

❖To switch between pages or select functions:

Press the scroll key.

❖To stop the machine during a multi- copy run:

Press the {Clear/Stop} key.

❖To return the machine to the initial condition after copying:

Press the {Clear Modes} key.

❖To clear an entered value.

Press the {Clear/Stop} key.

21

Image 29

Contents Copy Reference Introduction Manuals for This Machine Other manuals Manuals for DeskTopBinder V2 LiteManuals for ScanRouter V2 Lite Table of Contents Settings You Can Change with User Tools Accessing User Tools Copier FeaturesDos and Donts Where to Put Your Machine If Your Machine Does Not Operate As You WantCombination Chart Supplementary Information SpecificationsPage Page Remarque concernant les utilisateurs au Canada Avertissement Names of Major Options How to Read This ManualSymbols Safety During Operation Safety InformationPage AAI029S Machine Types Copier only Options fully installedControl Panel Combine/Series key Cancel keySort key Lighter and DarkerInitial copy display Reading the Display and Using KeysDisplay Scroll keys Turning On the Main Power Turning On the PowerTurning On the Power Operation switch right side of the control panelTurning Off the Main Power Turning Off the PowerSaving Energy Auto Off/ Low PowerOriginals Sizes and Weights of Recommended OriginalsMetric version Inch versionSizes Detectable with Auto Paper Select Exposure glass Missing Image AreaADF or Ardf Sizes difficult to detectPlacing Originals on the Exposure Glass Placing OriginalsOriginal Orientation Limit mark Document guide ArdfPlacing custom size originals To switch between pages or select functions Basic ProcedureTo stop the machine during a multi- copy run To clear an entered valueOpen the bypass tray Copying from the Bypass TrayPush up the paper guide release lever Paper guide release leverSelect Regular Size using U or T, and then press the OK key Select Paper Size using U or T, and then press the OK keyHorizontal size Vertical size Extender Paper guides Pull down the paper guide release the lever step BSelect Custom Size using U or T, and then press the OK key Select Paper Size using U orFeeds Then press the OKSelect Thick Paper using U or T, and then press the OK key Selecting Original Type Setting Adjusting Image DensityCopier Functions Selecting Copy PaperMake sure Auto Paper Select is se- lected Preset Reduce/EnlargeSelect the paper tray or bypass tray using U or T Press Reduce or Enlarge ZoomBase Point Auto Reduce/Enlarge Adjust the ratio using U or TEnter the ratio Press the OK keySort SortRotate Sort Sided → 2 Sided Duplex Type 3 onlySided → 2 Sided Optional Ardf is required Select Sort or Rotate Sort, and then press the OK keyPress the Duplex key Original orientation and completed copiesSided 2 Pages → Combine 1 Side One-Sided CombineSided 4 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is requiredPosition of combine Optional Ardf is requiredSided 2 Pages → Combine 1 Side Orientation of the original and imageSided 8 Pages → Combine 2 Side Two-Sided Combine Type 3 onlySided 4 Pages → Combine 2 Side Optional Ardf is required Sided 4 Pages → Combine 2 SideThen press the OK key Top or Top to Bottom using U orSided→1 Sided Optional Ardf is required Series CopiesBook→1 Sided Press the Combine/Series keyPlace your original, and then press the Start key Select the paper tray using U or TIf Your Machine Does Not Operate As You Want When a Message Is DisplayedIf You Cannot Make Clear Copies Problem Causes SolutionsBasic If You Cannot Make Copies As You WantEdit CombineDuplex Type 3 only When Memory Is FullPush the paper tray in, until it stops Loading PaperLoading Paper Original Orientation Orientation-Fixed Paper or Two-Sided PaperLoaded paper orientation For MFP Handling Toner Adding TonerToner Storage Used TonerRemoving Toner Inserting Toner Troubleshooting Press the User Tools/Counter key Accessing User Tools Copier FeaturesChanging Default Settings Change is made, and the ma- chine is ready to copy Quitting User ToolsAuto Tray Switching Settings You Can Change with User ToolsOriginal Type Setting APS/ Auto R/E PriorityOrientation Duplex Mode PriorityMax. Number of Sets Original Count DisplayLetterhead Setting Preset R/E PriorityDuplex Margin Rotate SortUser Tools Copier Features Dos and Donts RemarksMachine Environment Where to Put Your MachineOptimum environmental conditions Environments to avoidMoving Power ConnectionAccess to the Machine Cleaning the Exposure Glass Cover Cleaning the Exposure GlassCleaning the ADF or Ardf Cleaning the machineRemarks Combination Chart SpecificationsBypass Tray Copy Preset Enlarge/ReduceSupplementary Information Sort, Rotate Sort ZoomDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607