Savin 4018d, 4015 manual Access to the Machine

Page 68

KirC2_ENcopyF_FM.book Page 60 Monday, September 22, 2003 11:36 AM

Remarks

5

60

Access to the Machine

Place the machine near the power source, providing the clearance areas shown.

1.Rear: 5 cm (2") or more

2.Right: 25 cm (10") or more

3.Front: 75 cm (29.6") or more

4.Left: 15 cm (6") or more

Note

❒For the required space when op- tions are installed, contact your service representative.

Image 68

Contents Copy Reference Introduction Manuals for This Machine Other manuals Manuals for DeskTopBinder V2 LiteManuals for ScanRouter V2 Lite Table of Contents Accessing User Tools Copier Features Settings You Can Change with User ToolsDos and Donts Where to Put Your Machine If Your Machine Does Not Operate As You WantSpecifications Combination Chart Supplementary InformationPage Page Remarque concernant les utilisateurs au Canada Avertissement Names of Major Options How to Read This ManualSymbols Safety Information Safety During OperationPage AAI029S Machine Types Copier only Options fully installedControl Panel Cancel key Combine/Series keySort key Lighter and DarkerInitial copy display Reading the Display and Using KeysDisplay Scroll keys Turning On the Power Turning On the Main PowerTurning On the Power Operation switch right side of the control panelTurning Off the Power Turning Off the Main PowerAuto Off/ Low Power Saving EnergySizes and Weights of Recommended Originals OriginalsMetric version Inch versionSizes Detectable with Auto Paper Select Missing Image Area Exposure glassADF or Ardf Sizes difficult to detectPlacing Originals on the Exposure Glass Placing OriginalsOriginal Orientation Ardf Limit mark Document guidePlacing custom size originals Basic Procedure To switch between pages or select functionsTo stop the machine during a multi- copy run To clear an entered valueCopying from the Bypass Tray Open the bypass trayPush up the paper guide release lever Paper guide release leverSelect Paper Size using U or T, and then press the OK key Select Regular Size using U or T, and then press the OK keyHorizontal size Vertical size Extender Paper guides Pull down the paper guide release the lever step BSelect Paper Size using U or Select Custom Size using U or T, and then press the OK keyFeeds Then press the OKSelect Thick Paper using U or T, and then press the OK key Adjusting Image Density Selecting Original Type SettingCopier Functions Selecting Copy PaperMake sure Auto Paper Select is se- lected Preset Reduce/EnlargeSelect the paper tray or bypass tray using U or T Press Reduce or Enlarge ZoomBase Point Adjust the ratio using U or T Auto Reduce/EnlargeEnter the ratio Press the OK keySort SortRotate Sort Duplex Type 3 only Sided → 2 SidedSided → 2 Sided Optional Ardf is required Select Sort or Rotate Sort, and then press the OK keyOriginal orientation and completed copies Press the Duplex keyOne-Sided Combine Sided 2 Pages → Combine 1 SideSided 4 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is requiredOptional Ardf is required Position of combineSided 2 Pages → Combine 1 Side Orientation of the original and imageTwo-Sided Combine Type 3 only Sided 8 Pages → Combine 2 SideSided 4 Pages → Combine 2 Side Optional Ardf is required Sided 4 Pages → Combine 2 SideTop or Top to Bottom using U or Then press the OK keySeries Copies Sided→1 Sided Optional Ardf is requiredBook→1 Sided Press the Combine/Series keySelect the paper tray using U or T Place your original, and then press the Start keyWhen a Message Is Displayed If Your Machine Does Not Operate As You WantProblem Causes Solutions If You Cannot Make Clear CopiesIf You Cannot Make Copies As You Want BasicEdit CombineWhen Memory Is Full Duplex Type 3 onlyPush the paper tray in, until it stops Loading PaperLoading Paper Orientation-Fixed Paper or Two-Sided Paper Original OrientationLoaded paper orientation For MFP Adding Toner Handling TonerToner Storage Used TonerRemoving Toner Inserting Toner Troubleshooting Press the User Tools/Counter key Accessing User Tools Copier FeaturesChanging Default Settings Quitting User Tools Change is made, and the ma- chine is ready to copySettings You Can Change with User Tools Auto Tray SwitchingOriginal Type Setting APS/ Auto R/E PriorityDuplex Mode Priority OrientationMax. Number of Sets Original Count DisplayPreset R/E Priority Letterhead SettingDuplex Margin Rotate SortUser Tools Copier Features Remarks Dos and DontsWhere to Put Your Machine Machine EnvironmentOptimum environmental conditions Environments to avoidPower Connection MovingAccess to the Machine Cleaning the Exposure Glass Cleaning the Exposure Glass CoverCleaning the ADF or Ardf Cleaning the machineRemarks Specifications Combination ChartBypass Tray Copy Preset Enlarge/ReduceSupplementary Information Zoom Sort, Rotate SortDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607