Savin 4018d, 4015 Maintaining Your Machine, Cleaning the Exposure Glass, Cleaning the ADF or Ardf

Page 69

KirC2_ENcopyF_FM.book Page 61 Monday, September 22, 2003 11:36 AM

Maintaining Your Machine

Maintaining Your Machine

If the exposure glass, exposure glass cover, ADF belt, or ARDF belt is dirty, copy clarity may be reduced. Clean these parts if they are dirty.

❖Cleaning the machine

Wipe the machine with a soft, damp cloth. Then wipe it with a dry cloth to remove the water.

Important

❒Do not use chemical cleaner or or- ganic solvents such as thinner or benzene. If such substances get in- side the machine or melt plastic parts, a failure might occur.

❒Do not clean parts other than those explicitly specified in this manual. Other parts should only be cleaned by your service representative.

Cleaning the Exposure Glass

ND1C0200

Cleaning the Exposure Glass Cover

TRSR140E

5

Cleaning the ADF or ARDF

61

Image 69

Contents Copy Reference Introduction Manuals for This Machine Manuals for DeskTopBinder V2 Lite Manuals for ScanRouter V2 LiteOther manuals Table of Contents Settings You Can Change with User Tools Accessing User Tools Copier FeaturesDos and Donts Where to Put Your Machine If Your Machine Does Not Operate As You WantCombination Chart Supplementary Information SpecificationsPage Page Remarque concernant les utilisateurs au Canada Avertissement How to Read This Manual SymbolsNames of Major Options Safety During Operation Safety InformationPage AAI029S Machine Types Options fully installed Control PanelCopier only Combine/Series key Cancel keySort key Lighter and DarkerReading the Display and Using Keys DisplayInitial copy display Scroll keys Turning On the Main Power Turning On the PowerTurning On the Power Operation switch right side of the control panelTurning Off the Main Power Turning Off the PowerSaving Energy Auto Off/ Low PowerOriginals Sizes and Weights of Recommended OriginalsMetric version Inch versionSizes Detectable with Auto Paper Select Exposure glass Missing Image AreaADF or Ardf Sizes difficult to detectPlacing Originals Original OrientationPlacing Originals on the Exposure Glass Limit mark Document guide ArdfPlacing custom size originals To switch between pages or select functions Basic ProcedureTo stop the machine during a multi- copy run To clear an entered valueOpen the bypass tray Copying from the Bypass TrayPush up the paper guide release lever Paper guide release leverSelect Regular Size using U or T, and then press the OK key Select Paper Size using U or T, and then press the OK keyHorizontal size Vertical size Extender Paper guides Pull down the paper guide release the lever step BSelect Custom Size using U or T, and then press the OK key Select Paper Size using U orFeeds Then press the OKSelect Thick Paper using U or T, and then press the OK key Selecting Original Type Setting Adjusting Image DensityCopier Functions Selecting Copy PaperPreset Reduce/Enlarge Select the paper tray or bypass tray using U or TMake sure Auto Paper Select is se- lected Zoom Base PointPress Reduce or Enlarge Auto Reduce/Enlarge Adjust the ratio using U or TEnter the ratio Press the OK keySort Rotate SortSort Sided → 2 Sided Duplex Type 3 onlySided → 2 Sided Optional Ardf is required Select Sort or Rotate Sort, and then press the OK keyPress the Duplex key Original orientation and completed copiesSided 2 Pages → Combine 1 Side One-Sided CombineSided 4 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is requiredPosition of combine Optional Ardf is requiredSided 2 Pages → Combine 1 Side Orientation of the original and imageSided 8 Pages → Combine 2 Side Two-Sided Combine Type 3 onlySided 4 Pages → Combine 2 Side Optional Ardf is required Sided 4 Pages → Combine 2 SideThen press the OK key Top or Top to Bottom using U orSided→1 Sided Optional Ardf is required Series CopiesBook→1 Sided Press the Combine/Series keyPlace your original, and then press the Start key Select the paper tray using U or TIf Your Machine Does Not Operate As You Want When a Message Is DisplayedIf You Cannot Make Clear Copies Problem Causes SolutionsBasic If You Cannot Make Copies As You WantEdit CombineDuplex Type 3 only When Memory Is FullLoading Paper Loading PaperPush the paper tray in, until it stops Original Orientation Orientation-Fixed Paper or Two-Sided PaperLoaded paper orientation For MFP Handling Toner Adding TonerToner Storage Used TonerRemoving Toner Inserting Toner Troubleshooting Accessing User Tools Copier Features Changing Default SettingsPress the User Tools/Counter key Change is made, and the ma- chine is ready to copy Quitting User ToolsAuto Tray Switching Settings You Can Change with User ToolsOriginal Type Setting APS/ Auto R/E PriorityOrientation Duplex Mode PriorityMax. Number of Sets Original Count DisplayLetterhead Setting Preset R/E PriorityDuplex Margin Rotate SortUser Tools Copier Features Dos and Donts RemarksMachine Environment Where to Put Your MachineOptimum environmental conditions Environments to avoidMoving Power ConnectionAccess to the Machine Cleaning the Exposure Glass Cover Cleaning the Exposure GlassCleaning the ADF or Ardf Cleaning the machineRemarks Combination Chart SpecificationsPreset Enlarge/Reduce Supplementary InformationBypass Tray Copy Sort, Rotate Sort ZoomDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607