Savin 4018d, 4015 manual Combine, Duplex Margin Type 3 only

Page 74

KirC2_ENcopyF_FM.book Page 66 Monday, September 22, 2003 11:36 AM

Specifications

❖Combine

•When using this function, the machine selects the reproduction ratio auto- matically. This reproduction ratio depends on copy paper sizes and the number of originals.

•The reproduction ratios you can specify are 50–200%.

•If the calculated ratio is under the minimum ratio, it is automatically ad- justed to within available range. However, with some ratios, parts of the image might not be copied.

•You cannot use custom size paper.

•If the orientation of originals is different from that of the copy paper, the machine will automatically rotate the image by 90° to make copies proper- ly.

•If the number of originals placed is less than the number specified for com- bining, the last page segment is left blank as shown.

6

❖Duplex Margin (Type 3 only)

•If you set a binding margin that is too wide, part of the image may not be copied.

•When making copies using the Combine function, the binding margin is added to the copies when combining is finished.

66

Image 74

Contents Copy Reference Introduction Manuals for This Machine Other manuals Manuals for DeskTopBinder V2 LiteManuals for ScanRouter V2 Lite Table of Contents Dos and Donts Where to Put Your Machine Accessing User Tools Copier FeaturesSettings You Can Change with User Tools If Your Machine Does Not Operate As You WantSpecifications Combination Chart Supplementary InformationPage Page Remarque concernant les utilisateurs au Canada Avertissement Names of Major Options How to Read This ManualSymbols Safety Information Safety During OperationPage AAI029S Machine Types Copier only Options fully installedControl Panel Sort key Cancel keyCombine/Series key Lighter and DarkerInitial copy display Reading the Display and Using KeysDisplay Scroll keys Turning On the Power Turning On the PowerTurning On the Main Power Operation switch right side of the control panelTurning Off the Power Turning Off the Main PowerAuto Off/ Low Power Saving EnergyMetric version Sizes and Weights of Recommended OriginalsOriginals Inch versionSizes Detectable with Auto Paper Select ADF or Ardf Missing Image AreaExposure glass Sizes difficult to detectPlacing Originals on the Exposure Glass Placing OriginalsOriginal Orientation Ardf Limit mark Document guidePlacing custom size originals To stop the machine during a multi- copy run Basic ProcedureTo switch between pages or select functions To clear an entered valuePush up the paper guide release lever Copying from the Bypass TrayOpen the bypass tray Paper guide release leverHorizontal size Vertical size Extender Paper guides Select Paper Size using U or T, and then press the OK keySelect Regular Size using U or T, and then press the OK key Pull down the paper guide release the lever step BFeeds Select Paper Size using U orSelect Custom Size using U or T, and then press the OK key Then press the OKSelect Thick Paper using U or T, and then press the OK key Copier Functions Adjusting Image DensitySelecting Original Type Setting Selecting Copy PaperMake sure Auto Paper Select is se- lected Preset Reduce/EnlargeSelect the paper tray or bypass tray using U or T Press Reduce or Enlarge ZoomBase Point Enter the ratio Adjust the ratio using U or TAuto Reduce/Enlarge Press the OK keySort SortRotate Sort Sided → 2 Sided Optional Ardf is required Duplex Type 3 onlySided → 2 Sided Select Sort or Rotate Sort, and then press the OK keyOriginal orientation and completed copies Press the Duplex keySided 4 Pages → Combine 1 Side One-Sided CombineSided 2 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is requiredSided 2 Pages → Combine 1 Side Optional Ardf is requiredPosition of combine Orientation of the original and imageSided 4 Pages → Combine 2 Side Optional Ardf is required Two-Sided Combine Type 3 onlySided 8 Pages → Combine 2 Side Sided 4 Pages → Combine 2 SideTop or Top to Bottom using U or Then press the OK keyBook→1 Sided Series CopiesSided→1 Sided Optional Ardf is required Press the Combine/Series keySelect the paper tray using U or T Place your original, and then press the Start keyWhen a Message Is Displayed If Your Machine Does Not Operate As You WantProblem Causes Solutions If You Cannot Make Clear CopiesEdit If You Cannot Make Copies As You WantBasic CombineWhen Memory Is Full Duplex Type 3 onlyPush the paper tray in, until it stops Loading PaperLoading Paper Orientation-Fixed Paper or Two-Sided Paper Original OrientationLoaded paper orientation For MFP Toner Storage Adding TonerHandling Toner Used TonerRemoving Toner Inserting Toner Troubleshooting Press the User Tools/Counter key Accessing User Tools Copier FeaturesChanging Default Settings Quitting User Tools Change is made, and the ma- chine is ready to copyOriginal Type Setting Settings You Can Change with User ToolsAuto Tray Switching APS/ Auto R/E PriorityMax. Number of Sets Duplex Mode PriorityOrientation Original Count DisplayDuplex Margin Preset R/E PriorityLetterhead Setting Rotate SortUser Tools Copier Features Remarks Dos and DontsOptimum environmental conditions Where to Put Your MachineMachine Environment Environments to avoidPower Connection MovingAccess to the Machine Cleaning the ADF or Ardf Cleaning the Exposure GlassCleaning the Exposure Glass Cover Cleaning the machineRemarks Specifications Combination ChartBypass Tray Copy Preset Enlarge/ReduceSupplementary Information Zoom Sort, Rotate SortDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607