Savin 4018d Where to Put Your Machine, Machine Environment, Optimum environmental conditions

Page 66

KirC2_ENcopyF_FM.book Page 58 Monday, September 22, 2003 11:36 AM

Remarks

Where to Put Your Machine

5

58

Machine Environment

Choose your machine's location care- fully. Environmental conditions greatly affect its performance.

Optimum environmental conditions

RCAUTION:

•Keep the machine away from hu- midity and dust. Otherwise a fire or an electric shock might occur.

•Do not place the machine on an unstable or tilted surface. If it top- ples over, an injury might occur.

RCAUTION:

•If you use the machine in a con- fined space, make sure there is a continuous air turnover.

•Temperature: 10-32 °C (50-89.6 °F) (humidity to be 54% at 32 °C, 89.6 °F)

•Humidity: 15-80% (temperature to be 27 °C, 80.6 °F at 80%)

•A strong and level base.

•The machine must be level within 5 mm, 0.2 inches: both front to rear, and left to right.

•To avoid possible buildup of ozone, be sure to locate this ma- chine in a large well ventilated room that has an air turnover of more than 30 m3/hr/person.

Environments to avoid

•Locations exposed to direct sun- light or other sources of strong light (more than 1,500 lux).

•Locations directly exposed to cool air from an air conditioner or heat- ed air from a heater. (Sudden tem- perature changes can cause condensation to form inside the machine.)

•Locations close to machines gener- ating ammonia, such as a diazo copy machine.

•Places where the machine will be subject to frequent strong vibra- tion.

•Dusty areas.

•Areas with corrosive gases.

Image 66

Contents Copy Reference Introduction Manuals for This Machine Manuals for DeskTopBinder V2 Lite Manuals for ScanRouter V2 LiteOther manuals Table of Contents Dos and Donts Where to Put Your Machine Accessing User Tools Copier FeaturesSettings You Can Change with User Tools If Your Machine Does Not Operate As You WantSpecifications Combination Chart Supplementary InformationPage Page Remarque concernant les utilisateurs au Canada Avertissement How to Read This Manual SymbolsNames of Major Options Safety Information Safety During OperationPage AAI029S Machine Types Options fully installed Control PanelCopier only Sort key Cancel keyCombine/Series key Lighter and DarkerReading the Display and Using Keys DisplayInitial copy display Scroll keys Turning On the Power Turning On the PowerTurning On the Main Power Operation switch right side of the control panelTurning Off the Power Turning Off the Main PowerAuto Off/ Low Power Saving EnergyMetric version Sizes and Weights of Recommended OriginalsOriginals Inch versionSizes Detectable with Auto Paper Select ADF or Ardf Missing Image AreaExposure glass Sizes difficult to detectPlacing Originals Original OrientationPlacing Originals on the Exposure Glass Ardf Limit mark Document guidePlacing custom size originals To stop the machine during a multi- copy run Basic ProcedureTo switch between pages or select functions To clear an entered valuePush up the paper guide release lever Copying from the Bypass TrayOpen the bypass tray Paper guide release leverHorizontal size Vertical size Extender Paper guides Select Paper Size using U or T, and then press the OK keySelect Regular Size using U or T, and then press the OK key Pull down the paper guide release the lever step BFeeds Select Paper Size using U orSelect Custom Size using U or T, and then press the OK key Then press the OKSelect Thick Paper using U or T, and then press the OK key Copier Functions Adjusting Image DensitySelecting Original Type Setting Selecting Copy PaperPreset Reduce/Enlarge Select the paper tray or bypass tray using U or TMake sure Auto Paper Select is se- lected Zoom Base PointPress Reduce or Enlarge Enter the ratio Adjust the ratio using U or TAuto Reduce/Enlarge Press the OK keySort Rotate SortSort Sided → 2 Sided Optional Ardf is required Duplex Type 3 onlySided → 2 Sided Select Sort or Rotate Sort, and then press the OK keyOriginal orientation and completed copies Press the Duplex keySided 4 Pages → Combine 1 Side One-Sided CombineSided 2 Pages → Combine 1 Side Sided 1 Page → Combine 1 Side Optional Ardf is requiredSided 2 Pages → Combine 1 Side Optional Ardf is requiredPosition of combine Orientation of the original and imageSided 4 Pages → Combine 2 Side Optional Ardf is required Two-Sided Combine Type 3 onlySided 8 Pages → Combine 2 Side Sided 4 Pages → Combine 2 SideTop or Top to Bottom using U or Then press the OK keyBook→1 Sided Series CopiesSided→1 Sided Optional Ardf is required Press the Combine/Series keySelect the paper tray using U or T Place your original, and then press the Start keyWhen a Message Is Displayed If Your Machine Does Not Operate As You WantProblem Causes Solutions If You Cannot Make Clear CopiesEdit If You Cannot Make Copies As You WantBasic CombineWhen Memory Is Full Duplex Type 3 onlyLoading Paper Loading PaperPush the paper tray in, until it stops Orientation-Fixed Paper or Two-Sided Paper Original OrientationLoaded paper orientation For MFP Toner Storage Adding TonerHandling Toner Used TonerRemoving Toner Inserting Toner Troubleshooting Accessing User Tools Copier Features Changing Default SettingsPress the User Tools/Counter key Quitting User Tools Change is made, and the ma- chine is ready to copyOriginal Type Setting Settings You Can Change with User ToolsAuto Tray Switching APS/ Auto R/E PriorityMax. Number of Sets Duplex Mode PriorityOrientation Original Count DisplayDuplex Margin Preset R/E PriorityLetterhead Setting Rotate SortUser Tools Copier Features Remarks Dos and DontsOptimum environmental conditions Where to Put Your MachineMachine Environment Environments to avoidPower Connection MovingAccess to the Machine Cleaning the ADF or Ardf Cleaning the Exposure GlassCleaning the Exposure Glass Cover Cleaning the machineRemarks Specifications Combination ChartPreset Enlarge/Reduce Supplementary InformationBypass Tray Copy Zoom Sort, Rotate SortDuplex Margin Type 3 only Index Combine, 34 orientation Orientation and completed copies Adding Handling Inserting Removing Storage Used Memo Means Power on EN USA B121-6607