Uniden USC 2500XL T manual Scan KEY

Page 9

LCD DISPLAY

SCAN KEY

The liquid crystal display (LCD) shows the current channel and frequency. It also

displays the mode, status, and bank indicators.

Press [SCAN] to start scanning all programmed channels that are not locked out. ("SCAN" appears on the display during scanning.)

MANUAL KEY In Scan or Search Mode, press [MANUAL] I to stop scanning or searching, and to select a channel. After you stop the scanner, press fMANUAL] again to STEP UP a channel or requency. Press and holdto rapidly step through the channels or frequencies. Use

the numeric keypad to enter a channel

number, and then press [MANUAL] to access the channel.

WX KEY There are 7 weather channels. Press

[WX]to find the active weather

channel in your area. ('WX' appears on the display in Weather Mode.)

Note: Currently the Weather Service is not available in Australia.

DELAY KEY

UO KEY

PRI KEY

Use [DL V] to turn ON or OFF the automatic

2-second delay during scanning or searching

for active frequencies. (In Delay Mode, "DLY" appears on the display.) In this mode, when

the scanner monitors an active frequency, searching or scanning will not resume until transmission stops for 2 seconds.

Press rUe] to "lock out" or prevent scanning

of the displaxed channel, including Priority Channels. ('ud' appears on the display.) To

unlock a channel, press rUe] again. rUe] can be used in Manual Mode, or Scan Mode, only on programmed channels. To display locked out channels, turn the Rotary Tuner,

or press [HLD], [LMT], [MANUAL] to manually step through the selected bank. (Note: Locking

out a channel will not erase the programmed

frequency.)

You can assign "priority" to one channel in each of Banks 1 through 10. To assign priority, first display the selected channel, and then press and hold [PRI] for more than

2.5seconds. A "P" appears on the display beside the Priority Channel. In Priority Mode, the scanner monitors the Priority Channel(s) every 2 seconds. If activity is detected, the

scanner monitors that channel until no signal is present. ("PRt' appears on the display.)

7

Image 9
Contents USC 2500XL T This equipment contains a Nickel-Cadmium PrecautionsTable of Contents About Your New UBC 2500XLT Leather-like Carrying Case UnpackingWeather Channels Lets your scanner function as a Auto Store Automatically stores all active frequenciesAustralia TopView Controls and IndicatorsFrontView Scan KEY @ @4 Display. Note Youcannotdeactivateall20 banks LMTLIntKV Frequency. To store the same frequency into Send KEY Hold UO WX 1 2 KHz AM NFM WFM IkeylockiSetup Mounting the Flexible Antenna Installing the Belt ClipScanning Overview Bank Scan If you have programmed channels, youBand Search The Search function is different from Programming Channels 0 5Then, press Manual ProgrammingWith the Rotary Tuner If the selected channel already has a stored Frequency Example Set search limits of 137.000 to 144.000 MHz Ress Manual to stop scanningPress SRC to start the search HLD to stay on that frequencyPress Manual to stop scanning Auto Store feature automatically stores all activeFirst enter the lower limit by pressing 4 0 0 Press LMTDisplay. In this case, select another bank ~nother Open ChannelPress E Current channel is erased, and the display shows Deleting a Stored FrequencyPress Manual again Scann ingWeather Channel Scanning Customizing Scanner Operation Press Scan to start scanning This feature is active in Manual Mode or Scan ModeSetting Up Priority Channels To activate the Count feature Using Count to Monitor Channel ActivityTurn the scanner off before removing the Battery Pack Care and MaintenanceEvent of memory loss. If memory is lost, simply Reprogram each channelDo not use excessive amounts of water Clean the outside of the scanner with a mild detergentProblem TroubleshootingSearch Band Technical SpecificationsDisplay 137 174 222 400 520Warranty Unid~n~GP