Weed Eater 2600 manual Supported Standards, MIBs, and RFCs, Prerequisites

Page 10

Cisco High-Density Analog Voice and Fax Network Module

Supported Standards, MIBs, and RFCs

Table 2 lists the hardware platforms that support this feature, and the releases in which the feature was first supported. If the First T train Release column is blank, the feature is not yet available in a Cisco IOS T release on that platform.

 

Table 2

Cisco IOS Release and Platform Support for this Feature

 

 

 

 

 

Platform

 

12.2(2)XT

12.2(8)T

 

 

 

 

 

 

Cisco 2600 series

 

X

 

X

 

 

 

 

 

 

Cisco 3640

 

X

 

X

 

 

 

 

 

 

Cisco 3660

 

X

 

X

 

 

 

 

 

 

Supported Standards, MIBs, and RFCs

Standards

No new or modified Standards are supported by this feature.

MIBs

No new or modified MIBs are supported by this feature.

To obtain lists of supported MIBs by platform and Cisco IOS release, and to download MIB modules, go to the Cisco MIB website on Cisco.com at the following URL:

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

RFCs

No new or modified RFCs are supported by this feature.

Prerequisites

Obtain analog line or analog trunk service from your PBX, Key System, or PSTN.

Complete your company’s dial plan.

Establish a working telephony network based on your company’s dial plan.

Install at least one other network module or WAN interface card to provide the connection to the network LAN or WAN.

Establish a working IP and Frame Relay or ATM network. For more information about configuring IP, refer to the Cisco IOS IP Configuration Guide, Release 12.2.

Install appropriate voice processing and voice interface hardware on the router. See the “Configuring Analog FXO and FXS Voice Ports” section on page 11.

Cisco IOS Release 12.2(2)XT and 12.2(8)T

10

Image 10
Contents Feature History Release Modification Cisco High-Density Analog Voice and Fax Network ModuleVoice Port Numbers Feature OverviewBase Module InterfaceTelephony Signaling Interfaces FXS and FXO InterfacesDisconnect Supervision Commands FXO Supervisory Disconnect Tone Commands Delay in Voice NetworksEcho Cancellation Voice Level AdjustmentAdaptive Jitter Buffering Benefits Voice Activity Detection CommandsServiceability Cost EffectiveSupported Medium-Complexity Codecs RestrictionsSupported High-Complexity Codecs Supported low-Complexity CodecsRelated Documents Supported PlatformsCisco 2600 series Supported Standards, MIBs, and RFCs PrerequisitesCommand Purpose Configuration TasksConfiguring Analog FXO and FXS Voice Ports FXO or FXSDefault is the pattern specified by the cptone Keyword default is 25 on Cisco 2600 seriesDefault is Locale that has been configuredConfiguring Voice Activity Detection VAD Fine-Tuning Analog Voice PortsConfiguring Disconnect Supervision Commands For FXO ports-Use the no battery-reversal Enables battery reversal. The default is that batteryReversal is enabled Command to configure a loop-start voice port to notConfiguring FXO Supervisory Disconnect Tone Commands Exits voice class configuration mode From 0 to 1000 0 ms to 10 sec. The default isSec. The default is Voice network module is installedConfiguring Timeouts Commands Timing Commands Voice Quality Tuning Commands Configuring Adaptive Jitter AdjustmentConfiguring Echo Adjustment Configuring Voice Level AdjustmentVerifying Analog Voice-Port Configurations Platform Command SyntaxTroubleshooting Tips Troubleshooting Chart, Voice Port Testing Commands,Reconfigure the voice port Troubleshooting ChartProblem Suggested Action Keyword setting also called region tone is USVoice Port Testing Commands Configuring Voice Level Adjustment section onDetector-Related Function Tests Loopback Function TestsTone Injection Tests Relay-Related Function TestsTest. Enter the keyword disable to return Fax/Voice Mode TestsKeyword fax to force the voice port into fax mode Voice port to voice modeConfiguration Examples Analog FXO Voice Port ExampleAnalog FXS Voice Port Example Command Reference Debug dspapi, Debug hpi,Syntax Description Defaults Command Modes Command HistoryDebug dspapi Release ModificationRelated Commands Description Debug hpi DefaultsCommand Modes Command History Usage Guidelines ExamplesVoice-port Global configurationTo global configuration mode Cisco 2600, and Cisco 3600 RouterDial-peer voice EncapsulationGlossary
Related manuals
Manual 9 pages 15.51 Kb