Weed Eater 2600 Optional Specifies a tone cadence pattern to be, Cycle of the cadence pattern

Page 17

Cisco High-Density Analog Voice and Fax Network Module

Configuration Tasks

 

Command

Purpose

Step 10

 

 

Router(config-voice-class)# cadence-listcadence-id

(Optional) Specifies a tone cadence pattern to be

 

cycle-1-on-time cycle-1-off-time cycle-2-on-time

detected. Specify an on time and off time for each

 

cycle-2-off-time cycle-3-on-time cycle-3-off-time

cycle of the cadence pattern.

 

cycle-4-on-time cycle-4-off-time

 

 

 

 

 

The arguments are as follows:

 

 

cadence-id—Ranges from 1 to 10. There is no

 

 

 

default.

 

 

cycle-N-on-time and cycle-N-off-time—Range

 

 

 

from 0 to 1000 (0 ms to 10 sec). The default is

 

 

 

0.

Step 11

 

 

Router(config-voice-class)# cadence-variationtime

(Optional) Specifies the maximum time that the

 

 

tone onset can vary from the specified onset time

 

 

and still be detected, in 10-millisecond increments.

 

 

The time argument ranges from 0 to 200 (0 ms to 2

 

 

sec). The default is 0.

Step 12

 

 

Router(config-voice-class)# exit

Exits voice class configuration mode.

Step 13

 

 

Router(config)# voice-portslot/subunit/port

Enters voice-port configuration mode.

 

 

The arguments are as follows:

 

 

slot—Specifies the slot number where the

 

 

 

voice network module is installed.

 

 

subunit—Specifies the

 

 

 

Cisco High-Density Analog Voice/Fax Netwo

 

 

 

rk Module (NM-HDA) where the voice port is

 

 

 

located.

 

 

port—Identifies the analog voice-port number.

 

 

 

See Table 1 on page 2 for valid entries.

Step 14

 

 

Router(config-voiceport)# supervisory disconnect

Assigns an FXO supervisory disconnect tone voice

 

dualtone {mid-call pre-connect}voice-class tag

class to the voice port.

 

 

The keywords are as follows:

 

 

mid-call—Specifies tone detection during the

 

 

 

entire call.

 

 

pre-connect—Specifies tone detection only

 

 

 

during call setup.

Step 15

 

 

Router(config-voiceport)# supervisory disconnect

Configures the voice port to disconnect on receipt

 

anytone

of any tone.

 

 

 

 

Cisco IOS Release 12.2(2)XT and 12.2(8)T

17

Image 17
Contents Cisco High-Density Analog Voice and Fax Network Module Feature History Release ModificationBase Module Feature OverviewVoice Port Numbers InterfaceFXS and FXO Interfaces Telephony Signaling InterfacesDisconnect Supervision Commands Delay in Voice Networks FXO Supervisory Disconnect Tone CommandsAdaptive Jitter Buffering Voice Level AdjustmentEcho Cancellation Serviceability Voice Activity Detection CommandsBenefits Cost EffectiveSupported High-Complexity Codecs RestrictionsSupported Medium-Complexity Codecs Supported low-Complexity CodecsCisco 2600 series Supported PlatformsRelated Documents Prerequisites Supported Standards, MIBs, and RFCsConfiguring Analog FXO and FXS Voice Ports Configuration TasksCommand Purpose FXO or FXSDefault is Keyword default is 25 on Cisco 2600 seriesDefault is the pattern specified by the cptone Locale that has been configuredFine-Tuning Analog Voice Ports Configuring Voice Activity Detection VADConfiguring Disconnect Supervision Commands Reversal is enabled Enables battery reversal. The default is that batteryFor FXO ports-Use the no battery-reversal Command to configure a loop-start voice port to notConfiguring FXO Supervisory Disconnect Tone Commands Sec. The default is From 0 to 1000 0 ms to 10 sec. The default isExits voice class configuration mode Voice network module is installedConfiguring Timeouts Commands Timing Commands Configuring Adaptive Jitter Adjustment Voice Quality Tuning CommandsConfiguring Voice Level Adjustment Configuring Echo AdjustmentPlatform Command Syntax Verifying Analog Voice-Port ConfigurationsTroubleshooting Chart, Voice Port Testing Commands, Troubleshooting TipsProblem Suggested Action Troubleshooting ChartReconfigure the voice port Keyword setting also called region tone is USConfiguring Voice Level Adjustment section on Voice Port Testing CommandsLoopback Function Tests Detector-Related Function TestsRelay-Related Function Tests Tone Injection TestsKeyword fax to force the voice port into fax mode Fax/Voice Mode TestsTest. Enter the keyword disable to return Voice port to voice modeAnalog FXO Voice Port Example Configuration ExamplesAnalog FXS Voice Port Example Debug dspapi, Debug hpi, Command ReferenceDebug dspapi Defaults Command Modes Command HistorySyntax Description Release ModificationRelated Commands Description Command Modes Command History DefaultsDebug hpi Usage Guidelines ExamplesTo global configuration mode Global configurationVoice-port Cisco 2600, and Cisco 3600 RouterEncapsulation Dial-peer voiceGlossary
Related manuals
Manual 9 pages 15.51 Kb