Weed Eater 2600 manual Configuration Examples, Analog FXO Voice Port Example

Page 29

Cisco High-Density Analog Voice and Fax Network Module

Configuration Examples

Configuration Examples

This section provides the following voice port configuration examples:

•Analog FXO Voice Port Example

•Analog FXS Voice Port Example

Analog FXO Voice Port Example

The following example shows analog FXO output for voice-port configuration:

voice-port 1/0/4 no vad

timeouts call-disconnect 3 timeouts wait-release 3 connection trunk 8004 answer-mode supervisory disconnect dualtone pre-connect supervisory answer dualtone

no battery-reversal

!

voice-port 1/0/5 no vad

timeouts call-disconnect 3 timeouts wait-release 3 connection trunk 8005 answer-mode supervisory disconnect dualtone pre-connect supervisory answer dualtone

no battery-reversal

!

voice-port 1/0/6 no vad

timeouts call-disconnect 3 timeouts wait-release 3 connection trunk 8006 answer-mode supervisory disconnect dualtone pre-connect supervisory answer dualtone

no battery-reversal

!

voice-port 1/0/7 no vad

timeouts call-disconnect 3 timeouts wait-release 3 connection trunk 8007 answer-mode supervisory disconnect dualtone pre-connect supervisory answer dualtone

no battery-reversal

!

Cisco IOS Release 12.2(2)XT and 12.2(8)T

29

Image 29

Contents Cisco High-Density Analog Voice and Fax Network Module Feature History Release ModificationBase Module Feature OverviewVoice Port Numbers InterfaceFXS and FXO Interfaces Telephony Signaling InterfacesDisconnect Supervision Commands Delay in Voice Networks FXO Supervisory Disconnect Tone CommandsAdaptive Jitter Buffering Voice Level AdjustmentEcho Cancellation Serviceability Voice Activity Detection CommandsBenefits Cost EffectiveSupported High-Complexity Codecs RestrictionsSupported Medium-Complexity Codecs Supported low-Complexity CodecsCisco 2600 series Supported PlatformsRelated Documents Prerequisites Supported Standards, MIBs, and RFCsConfiguring Analog FXO and FXS Voice Ports Configuration TasksCommand Purpose FXO or FXSDefault is Keyword default is 25 on Cisco 2600 seriesDefault is the pattern specified by the cptone Locale that has been configuredFine-Tuning Analog Voice Ports Configuring Voice Activity Detection VADConfiguring Disconnect Supervision Commands Reversal is enabled Enables battery reversal. The default is that batteryFor FXO ports-Use the no battery-reversal Command to configure a loop-start voice port to notConfiguring FXO Supervisory Disconnect Tone Commands Sec. The default is From 0 to 1000 0 ms to 10 sec. The default isExits voice class configuration mode Voice network module is installedConfiguring Timeouts Commands Timing Commands Configuring Adaptive Jitter Adjustment Voice Quality Tuning CommandsConfiguring Voice Level Adjustment Configuring Echo AdjustmentPlatform Command Syntax Verifying Analog Voice-Port ConfigurationsTroubleshooting Chart, Voice Port Testing Commands, Troubleshooting TipsProblem Suggested Action Troubleshooting ChartReconfigure the voice port Keyword setting also called region tone is USConfiguring Voice Level Adjustment section on Voice Port Testing CommandsLoopback Function Tests Detector-Related Function TestsRelay-Related Function Tests Tone Injection TestsKeyword fax to force the voice port into fax mode Fax/Voice Mode TestsTest. Enter the keyword disable to return Voice port to voice modeAnalog FXO Voice Port Example Configuration ExamplesAnalog FXS Voice Port Example Debug dspapi, Debug hpi, Command ReferenceDebug dspapi Defaults Command Modes Command HistorySyntax Description Release ModificationRelated Commands Description Command Modes Command History DefaultsDebug hpi Usage Guidelines ExamplesTo global configuration mode Global configurationVoice-port Cisco 2600, and Cisco 3600 RouterEncapsulation Dial-peer voiceGlossary

Related manuals

Manual 9 pages 15.51 Kb