Panasonic UB-5315 installation manual For Your Safety, How to replace the fuse, Safety Information

Page 4

For Your Safety

English

CAUTION:

TO PREVENT RISK OF ELECTRIC SHOCK HAZARD, DO NOT REMOVE THE COVER OF THIS PRODUCT, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.

THE SOCKET-OUTLET MUST BE NEAR THIS EQUIPMENT AND MUST BE EASILY ACCESSIBLE.

The product should be used only with the power cord that is supplied by the manufacturer.

(220–240 V equipment)

A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord is not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 1.0 mm2).

CLASS 1 LED PRODUCT

4

For users in

the United Kingdom only

Safety Information

This appliance is supplied with a moulded three pin mains plug for your safety and convenience.

A 5 amp. fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps. and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer.

If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safely.

There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp. socket.

If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician.

WARNING: This appliance must be earthed.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code.

Green-and-Yellow: Earth

Blue:Neutral

Brown:Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured Green-and-Yellow must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or coloured Green or Green-and-Yellow.

The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N or coloured Black.

The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter L or coloured Red.

How to replace the fuse:

Open the fuse compartment with a screwdriver and replace the fuse.

Für Benutzer in der BRD

Hinweis:

Der arbeitsplatzbezogene Geräuschemissionswert dieses Gerätes beträgt 70 dB(A) nach DIN 45635 Teil 19.

Image 4
Contents UB-5815 Electronic BoardThank you for purchasing the Panasonic Electronic Board AccessoriesRecord these items for future reference Table of Contents How to replace the fuse For Your SafetySafety Information Precautions Precautions CD-ROMReplacing Part Names and Functions Part Names and Functions Control panel Panel Name DescriptionInstalling the Thermal Transfer Film Set the power switch to onPush down the printer open lever and open the printer door Insert the blue shaft into the front left holeInstalling the Thermal Transfer Film Loading Copy Paper Pull the paper cover forward as shown in the left figureLoading Copy Paper Close the paper cover until a click is heardMaking Copies Press the Copy KeyMaking Copies Copy types and procedures Copy Type Procedure Replacing the Thermal Transfer Film Paper Jams Remove the jammed paperInstall the thermal transfer film Paper JamsTurn the power on Close the paper coverLoosen the height adjustment handles Screen Height AdjustmentHang the screen in the desired slots of the slide plates Screen Height Adjustment Tighten the height adjustment handlesContents of CD-ROM Connecting the unit to a computerComputer Interfacing System requirementsInstalling the driver and software Installing the USB and Printer driver WindowsComputer Interfacing Check button and click the Next buttonWindows Me Special Note for Windows 98/Me Power on your computer and start Windows Although Digital Signature NotWindows XP UB5 USB Printer A4/Letter* driverClick the Install Panasonic-DMS Software button Installing Panasonic-DMS software and Twain driverClick on the desired language Removing the driver and software ScanningRemoving Panasonic-DMS software and Twain driver Acquire Image..., or clickComputer Interfacing Panaboard Operation Panel Printing Status BoxAbout Button Close ButtonDaily Care and Maintenance Cleaning the screen and the unitCleaning the printer head, platen roller and pick-up roller Caring for the eraserDaily Care and Maintenance Troubleshooting Symptom Care and Remedy SeeTroubleshooting Meanings of error codes Indication Cause Remedy SeeModel No UB-5315 UB-5815 SpecificationsOption and Separately available