Panasonic PT-LM2E manual Lamp Power

Page 48

		LAMP indicator

	Indicator	Illuminated (red)	Flashing (red)
	display	Illuminated (red)	Flashing (red)
	display

		It is nearly time to	An abnormality has been detected in the lamp
	Problem	replace the lamp	circuit.
		unit.

		BDoes “REPLACE	BThe power may	BThere may be an
	Possible	LAMP” appear on	have been turned	abnormality in the
	Possible	the screen after	on straight away	lamp circuit.
	cause	the screen after	on straight away	lamp circuit.
	cause	the projector is	after it was turned
		the projector is	after it was turned
		turned on?	off.

		BThis occurs when	BWait for a while	BDisconnect the
		the operation time	until the lamp unit	mains lead by
		for the lamp unit is	cools down before	following the
		nearing 1 800	turning the power	procedure on
		hours (when	back on again.	page 24, and then
		“LAMP POWER”		contact an
	Remedy	has been set to		Authorised
	Remedy	“HIGH”). Ask your		Service Centre.
		“HIGH”). Ask your		Service Centre.
		dealer or an
		Authorised
		Service Centre to
		replace the lamp
		unit.

NOTE:

BBe sure to disconnect the mains lead by following the procedure given in “Turning off the power” on page 24 before carrying out any of the procedures in the “Remedy” column.

BIf the power turns off after the TEMP indicator starts flashing, it means an abnormality has occurred. Please contact an Authorised Service Centre so that the necessary repairs can be made.

48-ENGLISH

Image 48

Contents LCD Projector Commercial Use Model No. PT-LM2EImportant Safety Notice Dear Panasonic CustomerFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Do not overload the mains socketDo not remove the cover or modify it in any way Do not handle the mains plug with wet hands Insert the mains plug securely into the mains socketDo not place the projector into water or let it become wet Do not place liquid containers on top of the projectorDo not use the projector in a bath or shower Do not look into the lens while the projector is being usedDo not cover the air inlet or the air outlet Always disconnect all cables before moving the projectorInsulate the battery using tape or similar before disposal Do not put your weight on this projectorUse only the specified batteries Accessories Before use Order to get the best picture quality Do not touch the surfaces of the lens with your bare handsScreen LampLeg adjuster buttons L/R Location and function of each part# Connector panel $ Air outlet port Remote control unit Projector control panel Top Menu$ Temp indicator Lamp indicatorRGB Input indicator Auto Setup button pages 23Video in connector pages 20 Audio in L-R jacks pages 19 Power input socket ACVideo in jack Security lockSetting-up Projection methodsProjector position Projection distancesConnecting to computer ConnectionsConnecting to video equipment Preparation for the remote control unit Insert the battery holderTurning on the power $Press the Power buttonTurn on the power of all connected devices Before turning on the power 1, Ensure that all peripheralPress the input select button to select the input signal Adjusting the angleAdjusting the size Adjusting the focusTurning off the power Press the Power buttonPower indicator Projector statusPress the Auto Setup button Pausing a picture Freeze Turning off the picture and sound momentarily ShutterPress the Freeze button Adjusting the volume Volume Remote control unit functions during D.ZOOM digital zoomPress the Volume +/- button Enlarging the picture D.ZOOMDisplaying two screens Index Window Press the Index Window buttonOn-screen menus Menu screensKeystone KeystoneSignal Power HighKEY Auto POW.OFF Disable OPTION1Menu operation guide PictureSelect ADJ Returning a setting to the factory default Picture ModeStandard PictureCorrecting keystone distortion Vertical keystone distortion correction onlyVertical OperationAdjusting the picture Picture ModeContrast DynamicBright ColorTint SharpnessStill Mode Signal ModeStill Mode Projecting sRGB-compatible picturesAdjusting the position Clock PhasePosition DOT ClockAspect Aspect AutoResizing Frame LockChanging the display language EnglishOption settings Auto SignalOSD Auto KeystnSxga Mode Lamp PowerBack Color FRONT/REARPower Memory Lamp RuntimeFunc Control KEYSetting up the security function Input PasswdAmend Passwd SecurityText Display Text ChangeTemp indicator Lamp indicator RemedyLamp Power Cleaning and replacing the air filter CleaningLamp unit replacement period Replacing the lamp unitLamp unit replacement procedure Lamp unit fixing screwsTime Reset OPTION2Runtime DESK/CEILING Desk FAN Control Standard LampBefore calling for service Problem Possible cause Not displayCorrectly Picture fromCleaning and maintenance Wipe the cabinet with a soft, dry clothSpecifications PAL60/SECAMRemote control unit OptionsList of compatible signals AppendixConnector pin wiring Projection dimensions calculation methodsPin No Dimensions Trademark acknowledgements