Panasonic PT-LM2E manual Specifications, PAL60/SECAM

Page 56

Specifications

Power supply:

100 V – 240 V ~, 50 Hz/60 Hz

Power consumption:

180 W [During standby (when fan is

 

stopped): Approx. 5 W]

Amps:

2.2 A – 1.0 A

LCD panel:

 

Panel size (diagonal):

0.55 type (13.97 mm)

Aspect ratio:

4:3

Display method:

3 transparent LCD panels (RGB)

Drive method:

Active matrix method

Pixels:

480 000 (800 x 600) x 3 panels

Lens:

Manual zoom (1 - 1.2) / Manual focus

 

F 1.8 - 1.9, f 17.0 mm - 20.4 mm

Lamp:

UHM lamp (130 W)

Luminosity:

1 400 lm

Scanning frequency (for RGB signals):

Horizontal scanning frequency:

15 kHz – 91 kHz

Vertical scanning frequency:

50 Hz – 85 Hz

Dot clock frequency:

Less than 100 MHz

YPBPR signals:

525i (480i), 525p (480p), 625i (576i),

 

625p (576p), 750p (720p), 1 125i (1 080i)

Colour system:

7 (NTSC/NTSC 4.43/PAL/PAL-M/PAL-N/

 

PAL60/SECAM)

Projection size:

838.2 mm - 7 620 mm (33˝ - 300˝)

Throw distance:

1.2 m - 10.9 m (3´11˝ - 35´9˝)

Optical axis shift:

6:1 (fixed)

Screen aspect ratio:

4:3

Installation:

Front/Rear/Ceiling/Desk (Menu selection

 

method)

Speaker:

2.8 cm round x 1

Max. useable volume output:

1 W (mono)

Connectors

 

RGB IN:

Single-line, D-SUB HD 15-pin (female)

During YPBPR input:

1.0 V [p-p] (Including sync), 75 Ω

Y:

PB, PR :

0.7 V [p-p], 75 Ω

During RGB input:

0.7 V [p-p], 75 Ω

R.G.B.:

G.SYNC:

1.0 V [p-p], 75 Ω

HD/SYNC:

TTL, automatic plus/minus polarity

 

compatible

VD:

TTL, automatic plus/minus polarity

 

compatible

56-ENGLISH

Page 55 Page 57
Image 56
Page 55 Page 57
Contents LCD Projector Commercial Use Model No. PT-LM2EImportant Safety Notice Dear Panasonic CustomerFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Do not remove the cover or modify it in any way Precautions with regard to safetyDo not overload the mains socket Do not handle the mains plug with wet hands Insert the mains plug securely into the mains socketDo not place the projector into water or let it become wet Do not place liquid containers on top of the projectorDo not use the projector in a bath or shower Do not look into the lens while the projector is being usedDo not cover the air inlet or the air outlet Always disconnect all cables before moving the projectorUse only the specified batteries Insulate the battery using tape or similar before disposalDo not put your weight on this projector Accessories Before use Order to get the best picture quality Do not touch the surfaces of the lens with your bare handsScreen LampLeg adjuster buttons L/R Location and function of each part# Connector panel $ Air outlet port Remote control unit Projector control panel Top Menu$ Temp indicator Lamp indicatorRGB Input indicator Auto Setup button pages 23Video in connector pages 20 Audio in L-R jacks pages 19 Power input socket ACVideo in jack Security lockSetting-up Projection methodsProjector position Projection distancesConnecting to computer ConnectionsConnecting to video equipment Preparation for the remote control unit Insert the battery holderTurning on the power $Press the Power buttonTurn on the power of all connected devices Before turning on the power 1, Ensure that all peripheralPress the input select button to select the input signal Adjusting the angleAdjusting the size Adjusting the focusTurning off the power Press the Power buttonPower indicator Projector statusPress the Auto Setup button Press the Freeze button Pausing a picture FreezeTurning off the picture and sound momentarily Shutter Adjusting the volume Volume Remote control unit functions during D.ZOOM digital zoomPress the Volume +/- button Enlarging the picture D.ZOOMDisplaying two screens Index Window Press the Index Window buttonOn-screen menus Menu screensKeystone KeystoneSignal Power HighKEY Auto POW.OFF Disable OPTION1Select ADJ Menu operation guidePicture Returning a setting to the factory default Picture ModeStandard PictureCorrecting keystone distortion Vertical keystone distortion correction onlyVertical OperationAdjusting the picture Picture ModeContrast DynamicBright ColorTint SharpnessStill Mode Signal ModeStill Mode Projecting sRGB-compatible picturesAdjusting the position Clock PhasePosition DOT ClockAspect Aspect AutoResizing Frame LockChanging the display language EnglishOption settings Auto SignalOSD Auto KeystnSxga Mode Lamp PowerBack Color FRONT/REARPower Memory Lamp RuntimeFunc Control KEYSetting up the security function Input PasswdAmend Passwd SecurityText Display Text ChangeTemp indicator Lamp indicator RemedyLamp Power Cleaning and replacing the air filter CleaningLamp unit replacement period Replacing the lamp unitLamp unit replacement procedure Lamp unit fixing screwsTime Reset OPTION2Runtime DESK/CEILING Desk FAN Control Standard LampBefore calling for service Problem Possible cause Not displayCorrectly Picture fromCleaning and maintenance Wipe the cabinet with a soft, dry clothSpecifications PAL60/SECAMRemote control unit OptionsList of compatible signals AppendixPin No Connector pin wiringProjection dimensions calculation methods Dimensions Trademark acknowledgements
Top Page Image Contents