Panasonic PT-LM2E manual Do not use the projector in a bath or shower

Page 7

Do not use the projector in a bath or shower.

BFire or electric shocks can result.

Do not look into the lens while the projector is being used.

BStrong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.

BBe especially careful not to let young children look into the lens. In addition, disconnect the mains lead when you are away from the projector.

Do not place your hands or other objects close to the air outlet port.

BHeated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand heat close to this port, otherwise burns or damage could result.

When replacing the lamp, allow it to cool for at least one hour before handling it.

BThe lamp cover gets very hot, and contact with it can cause burns.

Before replacing the lamp, be sure to disconnect the mains lead from the mains socket.

BElectric shocks or explosions can result if this is not done.

Caution

Do not cover the air inlet or the air outlet.

BDoing so may cause the projector to overheat, which can cause fire or damage to the projector.

BDo not place the projector in narrow, badly ventilated places such as closets or bookshelves.

BDo not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.

Do not set up the projector in humid or dusty places or in places where the projector may come into contact with smoke or steam.

BUsing the projector under such conditions may result in fire or electric shocks.

When disconnecting the mains lead, hold the plug, not the lead.

BIf the mains lead itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric shocks may result.

Always disconnect all cables before moving the projector.

BMoving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to occur.

Do not place any heavy objects on top of the projector.

BFailure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury.

Do not short-circuit, heat or disassemble the batteries or place them into water or fire.

BFailure to observe this may cause the batteries to overheat, leak, explode or catch fire, and burns or other injury may result.

Preparation

ENGLISH-7

Image 7
Contents Model No. PT-LM2E LCD Projector Commercial UseDear Panasonic Customer Important Safety NoticeImportant the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text CarefullyContents Do not overload the mains socket Precautions with regard to safetyDo not remove the cover or modify it in any way Do not place liquid containers on top of the projector Do not handle the mains plug with wet handsInsert the mains plug securely into the mains socket Do not place the projector into water or let it become wetAlways disconnect all cables before moving the projector Do not use the projector in a bath or showerDo not look into the lens while the projector is being used Do not cover the air inlet or the air outletDo not put your weight on this projector Insulate the battery using tape or similar before disposalUse only the specified batteries Accessories Before use Lamp Order to get the best picture qualityDo not touch the surfaces of the lens with your bare hands ScreenLocation and function of each part Leg adjuster buttons L/R# Connector panel $ Air outlet port Projector control panel Top Menu Remote control unitAuto Setup button pages 23 $ Temp indicatorLamp indicator RGB Input indicatorSecurity lock Video in connector pages 20Audio in L-R jacks pages 19 Power input socket AC Video in jackProjection methods Setting-upProjection distances Projector positionConnections Connecting to computerConnecting to video equipment Insert the battery holder Preparation for the remote control unitBefore turning on the power 1, Ensure that all peripheral Turning on the power$Press the Power button Turn on the power of all connected devicesAdjusting the focus Press the input select button to select the input signalAdjusting the angle Adjusting the sizePress the Power button Turning off the powerProjector status Power indicatorPress the Auto Setup button Turning off the picture and sound momentarily Shutter Pausing a picture FreezePress the Freeze button Enlarging the picture D.ZOOM Adjusting the volume VolumeRemote control unit functions during D.ZOOM digital zoom Press the Volume +/- buttonPress the Index Window button Displaying two screens Index WindowKeystone On-screen menusMenu screens KeystoneOPTION1 SignalPower High KEY Auto POW.OFF DisablePicture Menu operation guideSelect ADJ Picture Returning a setting to the factory defaultPicture Mode StandardOperation Correcting keystone distortionVertical keystone distortion correction only VerticalDynamic Adjusting the picturePicture Mode ContrastSharpness BrightColor TintProjecting sRGB-compatible pictures Still ModeSignal Mode Still ModeDOT Clock Adjusting the positionClock Phase PositionAspect Auto AspectFrame Lock ResizingEnglish Changing the display languageAuto Keystn Option settingsAuto Signal OSDFRONT/REAR Sxga ModeLamp Power Back ColorControl KEY Power MemoryLamp Runtime FuncSecurity Setting up the security functionInput Passwd Amend PasswdText Change Text DisplayRemedy Temp indicator Lamp indicatorLamp Power Cleaning Cleaning and replacing the air filterReplacing the lamp unit Lamp unit replacement periodLamp unit fixing screws Lamp unit replacement procedureDESK/CEILING Desk FAN Control Standard Lamp Time ResetOPTION2 RuntimeBefore calling for service Picture from Problem Possible causeNot display CorrectlyWipe the cabinet with a soft, dry cloth Cleaning and maintenancePAL60/SECAM SpecificationsOptions Remote control unitAppendix List of compatible signalsProjection dimensions calculation methods Connector pin wiringPin No Trademark acknowledgements Dimensions