Panasonic PT-LM2E manual Lamp unit replacement procedure, Lamp unit fixing screws

Page 51

	On-screen display	LAMP indicator
	Displayed for 30
More than 1 800 hours	seconds. Pressing any
More than 1 800 hours	button will clear the	Illuminates red during
	display.	image projection and
	Remains displayed until	standby mode.
More than 2 000 hours	Remains displayed until
More than 2 000 hours	any button is pressed.

Lamp unit replacement procedure

NOTE:

BIf the lamp usage time has passed 2 000 hours (when “LAMP POWER” has been set to “HIGH”), the projector will switch to standby mode after approximately 10 minutes of operation. The steps ) to - on the next page should thus be completed within 10 minutes.

#Disconnect the mains lead from the projector by following the procedure on page 24, and check that the area around the lamp unit has cooled down.

$Use a Phillips screwdriver to turn the lamp unit cover fixing screws at the bottom of the projector, and then remove the lamp unit cover.

Lamp unit cover

Lamp unit cover fixing screws

%Use a Phillips screwdriver to loosen the two lamp unit fixing screws until the screws turn freely. Then hold the handle of the lamp unit and gently pull it out from the projector.

Handle

	and maintenance
Lamp unit fixing screws	Care
Lamp unit fixing screws

&Insert the new lamp unit while making sure that the direction of insertion is correct, and then use a Phillips screwdriver to securely tighten the lamp unit fixing screws.

ENGLISH-51

Image 51

Contents Model No. PT-LM2E LCD Projector Commercial UseDear Panasonic Customer Important Safety NoticeImportant the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text CarefullyContents Precautions with regard to safety Do not overload the mains socketDo not remove the cover or modify it in any way Do not place liquid containers on top of the projector Do not handle the mains plug with wet handsInsert the mains plug securely into the mains socket Do not place the projector into water or let it become wetAlways disconnect all cables before moving the projector Do not use the projector in a bath or showerDo not look into the lens while the projector is being used Do not cover the air inlet or the air outletInsulate the battery using tape or similar before disposal Do not put your weight on this projectorUse only the specified batteries Accessories Before use Lamp Order to get the best picture qualityDo not touch the surfaces of the lens with your bare hands ScreenLocation and function of each part Leg adjuster buttons L/R# Connector panel $ Air outlet port Projector control panel Top Menu Remote control unitAuto Setup button pages 23 $ Temp indicatorLamp indicator RGB Input indicatorSecurity lock Video in connector pages 20Audio in L-R jacks pages 19 Power input socket AC Video in jackProjection methods Setting-upProjection distances Projector positionConnections Connecting to computerConnecting to video equipment Insert the battery holder Preparation for the remote control unitBefore turning on the power 1, Ensure that all peripheral Turning on the power$Press the Power button Turn on the power of all connected devicesAdjusting the focus Press the input select button to select the input signalAdjusting the angle Adjusting the sizePress the Power button Turning off the powerProjector status Power indicatorPress the Auto Setup button Pausing a picture Freeze Turning off the picture and sound momentarily ShutterPress the Freeze button Enlarging the picture D.ZOOM Adjusting the volume VolumeRemote control unit functions during D.ZOOM digital zoom Press the Volume +/- buttonPress the Index Window button Displaying two screens Index WindowKeystone On-screen menusMenu screens KeystoneOPTION1 SignalPower High KEY Auto POW.OFF DisableMenu operation guide PictureSelect ADJ Picture Returning a setting to the factory defaultPicture Mode StandardOperation Correcting keystone distortionVertical keystone distortion correction only VerticalDynamic Adjusting the picturePicture Mode ContrastSharpness BrightColor TintProjecting sRGB-compatible pictures Still ModeSignal Mode Still ModeDOT Clock Adjusting the positionClock Phase PositionAspect Auto AspectFrame Lock ResizingEnglish Changing the display languageAuto Keystn Option settingsAuto Signal OSDFRONT/REAR Sxga ModeLamp Power Back ColorControl KEY Power MemoryLamp Runtime FuncSecurity Setting up the security functionInput Passwd Amend PasswdText Change Text DisplayRemedy Temp indicator Lamp indicatorLamp Power Cleaning Cleaning and replacing the air filterReplacing the lamp unit Lamp unit replacement periodLamp unit fixing screws Lamp unit replacement procedureDESK/CEILING Desk FAN Control Standard Lamp Time ResetOPTION2 RuntimeBefore calling for service Picture from Problem Possible causeNot display CorrectlyWipe the cabinet with a soft, dry cloth Cleaning and maintenancePAL60/SECAM SpecificationsOptions Remote control unitAppendix List of compatible signalsConnector pin wiring Projection dimensions calculation methodsPin No Trademark acknowledgements Dimensions