Panasonic PT-LM2E manual Connector pin wiring, Projection dimensions calculation methods, Pin No

Page 59

Connector pin wiring

BThe pin layout and signal names for the S-VIDEO IN connector are shown below.

#$

%&

External view

Pin No.

Signal

#Earth (Luminance signal) $ Earth (Colour signal)

% Luminance signal & Colour signal

BThe pin layout and signal names for the RGB IN connector are shown below.

-1

(,

#'

External view

Pin No.

Signal

#R/PR

$G/G·SYNC/Y % B/PB

. SDA

/ HD/SYNC 0 VD

1 SCL

Pin & and + are spare.

Pins ' – *, , and - are for earth.

Pins . and 1 functions are only valid when supported by the computer.

Projection dimensions calculation methods

If the screen size (diagonal) is SD (m), then the following formula is used to calculate the projection distance for the wide lens position (LW) and the projection distance for the telephoto lens position (LT).

 

4:3

 

SH

 

H1

LW/LT

SW

Minimum Projection Distance (mm)

LW=30.919xSD/0.0254-42.514

Maximum Projection Distance (mm)

LT=36.766xSD/0.0254-42.233

For 16:9 aspect ratios, the following formula can be used to calculate the projection distance.

Minimum Projection Distance (mm)

LW=33.902xSD/0.0254-42.524

Maximum Projection Distance (mm)

LT=40.359xSD/0.0254-42.519

*The values obtained from the formulas above are approximate.

Others

ENGLISH-59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents
Model No. PT-LM2E LCD Projector Commercial UseDear Panasonic Customer Important Safety NoticeImportant the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text CarefullyContents Do not remove the cover or modify it in any way Precautions with regard to safetyDo not overload the mains socket Do not place liquid containers on top of the projector Do not handle the mains plug with wet handsInsert the mains plug securely into the mains socket Do not place the projector into water or let it become wetAlways disconnect all cables before moving the projector Do not use the projector in a bath or showerDo not look into the lens while the projector is being used Do not cover the air inlet or the air outletUse only the specified batteries Insulate the battery using tape or similar before disposalDo not put your weight on this projector Accessories Before use Lamp Order to get the best picture qualityDo not touch the surfaces of the lens with your bare hands ScreenLocation and function of each part Leg adjuster buttons L/R# Connector panel $ Air outlet port Projector control panel Top Menu Remote control unitAuto Setup button pages 23 $ Temp indicatorLamp indicator RGB Input indicatorSecurity lock Video in connector pages 20Audio in L-R jacks pages 19 Power input socket AC Video in jackProjection methods Setting-upProjection distances Projector positionConnections Connecting to computerConnecting to video equipment Insert the battery holder Preparation for the remote control unitBefore turning on the power 1, Ensure that all peripheral Turning on the power$Press the Power button Turn on the power of all connected devicesAdjusting the focus Press the input select button to select the input signalAdjusting the angle Adjusting the sizePress the Power button Turning off the powerProjector status Power indicatorPress the Auto Setup button Press the Freeze button Pausing a picture FreezeTurning off the picture and sound momentarily Shutter Enlarging the picture D.ZOOM Adjusting the volume VolumeRemote control unit functions during D.ZOOM digital zoom Press the Volume +/- buttonPress the Index Window button Displaying two screens Index WindowKeystone On-screen menusMenu screens KeystoneOPTION1 SignalPower High KEY Auto POW.OFF DisableSelect ADJ Menu operation guidePicture Picture Returning a setting to the factory defaultPicture Mode StandardOperation Correcting keystone distortionVertical keystone distortion correction only VerticalDynamic Adjusting the picturePicture Mode ContrastSharpness BrightColor TintProjecting sRGB-compatible pictures Still ModeSignal Mode Still ModeDOT Clock Adjusting the positionClock Phase PositionAspect Auto AspectFrame Lock ResizingEnglish Changing the display languageAuto Keystn Option settingsAuto Signal OSDFRONT/REAR Sxga ModeLamp Power Back ColorControl KEY Power MemoryLamp Runtime FuncSecurity Setting up the security functionInput Passwd Amend PasswdText Change Text DisplayRemedy Temp indicator Lamp indicatorLamp Power Cleaning Cleaning and replacing the air filterReplacing the lamp unit Lamp unit replacement periodLamp unit fixing screws Lamp unit replacement procedureDESK/CEILING Desk FAN Control Standard Lamp Time ResetOPTION2 RuntimeBefore calling for service Picture from Problem Possible causeNot display CorrectlyWipe the cabinet with a soft, dry cloth Cleaning and maintenancePAL60/SECAM SpecificationsOptions Remote control unitAppendix List of compatible signalsPin No Connector pin wiringProjection dimensions calculation methods Trademark acknowledgements Dimensions
Related manuals
Manual 60 pages 7.64 Kb