Panasonic PT-FW300NTU, PT-FW300U manual Power indicator, Switching the projector on/off

Page 22

Switching the projector on/off

Power indicator

The power indicator informs you the status of the power.

When the LAMP or TEMP indicator is flashing, you cannot switch on the power. See “TEMP, LAMP and FILTER Indicators” on page 47.

Power indicator

Basic Operation

	Indicator status		Status

	No illumination or flashing		The MAIN POWER is switched off.

		Lit	The MAIN POWER is switched on and the projector is in standby mode.
		Lit	When the LAMP or TEMP indicator is flashing, not available to switch on the power.

	RED
	RED		The power is switched off. (When NETWORK STANDBY in NETWORK menu or IN
		Flashing	STANDBY MODE of AUDIO SETTING in PROJECTOR SETUP menu is set to ON). Press
			the power button to start the projection.

	GREEN	Flashing	The power is switched on and the projector is getting ready to project.

		Lit	Projecting.
		Lit	Projecting.

		Lit	The power is switched off and the projector is cooling the lamp. The indicator will light or flash,
	ORANGE	Lit	and start the projection after a short time.
			and start the projection after a short time.

		Flashing	The power is switched on again when cooling the lamp and recovering to projection mode.

NOTE:

•If the projector is switched on again while the internal cooling fan is still operating by the internal power supply, it may take a while to start the projection.

•The electric consumption in standby mode is 4 W.

ENGLISH - 22

Image 22

Contents PT-FW300U Important Safety Notice Dear Panasonic CustomerTrade Name Important Safety NoticeDeclaration of Conformity PanasonicContents Contents SettingsMaintenance AppendixPrecautions with regard to safety Do not set up the projector outdoors Precautions with regard to safetyDo not look into the lens while the projector is being used Use only the specified batteries Remove the used batteries from the remote control promptlyDo not put your weight on this projector Do not mix old and new batteriesLiquid crystal panel SecurityOrder to get the best picture quality Optical componentsPower cord AccessoriesPower cord secure lock Minimum required setting screen Read this firstTop and front view About Your ProjectorProjector body Control panelSecurity lock Auto cleaning filter ACF Front leg Adjusters CompartmentAbout Your Projector Back and bottom view Lamp unit compartment Air exhaust portCLOCK, Clock Phase and Signal Search for Remote controlAttaching a hand strap Top view Remote control indicator Battery compartmentCalculation methods Setting upScreen size and throw distance Projection size 16 Throw distance LProjection method Front leg adjusters and throwing angleSetting up Mounting on the ceiling and projecting from frontHorizontal shift Adjusting the lens shift leverLens shift and positioning Vertical shiftWhen the screen position is fixed Setting up Projector location rangeWhen the projector position is fixed Before connection to the projector Connecting example ComputersConnections LAN terminalConnecting with DVI-D Connecting example AV equipmentConnecting with Video IN/S-VIDEO ConnectionsConnecting Switching the projector on/offPower cord Direct power on functionSwitching the projector on/off Power indicatorPower indicator informs you the status of the power Switch the Main Power on Press the power button Switching on the projectorSwitching off the projector Switch off the Main Power on the back of the projectorProjecting an image Selecting the input signalPositioning the image Operating range Remote control operationSetting up the image position automatically Facing to the projectorSwitching the input signal Enlarging the centered areaCapturing an image Resetting to the factory default settingsProjecting an image in INDEX-WINDOW mode Stopping the projectionSide by Side function signal combination table Using an assigned functionSwitching the signal Projecting 2 different source image at a timeDisable the Laser button Using the laser pointerControlling the volume of the speaker Laser pointer beam emitterInput Guide Menu NavigationMain menu and Sub-menu OSD DesignClosed Caption Setting Menu NavigationNavigating through the menu Adjusting with the bar scale itemsOperating procedure Displaying the Main menuPicture menu Digital Cinema Reality Color TemperatureDaylight View TV-SYSTEMPosition menu Aspect ratio options AspectPosition menu 169Frame Lock Display Option menu Closed Caption SettingScreen Setting DVI-DWide Mode Auto SetupSignal Search Sxga ModeOther Functions Display Option menuStatus Projector Setup menuNo Signal SHUT-OFF COMPUTER2 SelectAudio Setting InstallationHigh Altitude Mode Function ButtonInitialize ALL Filter Counter ResetTest Pattern Remaining Filter of Status in ProjectorSecurity menu PasswordPassword Change Text DisplayMenu Lock Menu Lock PasswordControl Device Setup Security menuItems in Network menu Wireless LAN PT-FW300NTUonlyNetwork menu Network menu, the following items are availableLamp indicator TEMP, Lamp and Filter IndicatorsManaging the indicated problems Temp indicatorCleaning the projector Care and ReplacementReplacing the Lamp unit When to replace the ACF Replacing the Auto Cleaning Filter ACFCare and Replacement Replacement procedure Before replacing the ACFTurn the projector upside down and place it gently Resetting the RemainingCounter Reset in Projector Setup On a soft clothTroubleshooting Quality*2 List of compatible signalsTechnical Information KHz MHzSerial terminal Computer connection guidance Technical Information Cable specificationsControl commands ProjectorInput signal Lamp switchingSwitching input Signals Remote terminalInstalling the safety cable Ceiling mount bracket safeguardsDVI-D in terminal SW m = SD x SH m = SD x Screen size and throw distance for 169 aspect ratioScreen size and throw distance for 43 aspect ratio LW m = 0.0339 x SD LT m = 0.0653 x SDSpecifications DVI-D VideoOUT AudioTrademark acknowledgements DimensionsUnit mm Index FunctionPicture Mode IndexPT-FW300NTU/PT-FW300U Avis important concernant la sécuritéNuméro de série Advertencia Avis important concernant la sécuritéAvertissement Déclaration de conformitéPrécautions de sécurité AvertissementMises EN Garde Précautions de sécuritéPrécautions lors du transport Précautions lors de linstallationPrécautions lors de lutilisation Affichage à cristaux liquides SécuritéComposants optiques Délai de remplacement de lUnité de la lampe Remplacement de lunité de la lampeAvant de remplacer le lUnité de la lampe Protections du support de montage au plafond Installation du câble de sécuritéRetirer et remplacer la lampe