Panasonic PT-FW300NTU manual Care and Replacement, Cleaning the projector, Replacing the Lamp unit

Page 48

Care and Replacement

Cleaning the projector

Before cleaning the projector

Switch off the MAIN POWER and disconnect the power plug from the wall outlet.

Unplug all the cables from the projector.

Cleaning the outer surface of the projector

Wipe off dirt and dust gently with a soft cloth.

If it is difficult to remove the dirt, soak a cloth with water, wring the cloth well and then wipe the projector. Dry off the projector with dry cloth.

If you use a chemical treated wipe, follow the instructions supplied with it.

Cleaning the lens and front glass surface

Wipe off dirt and dust gently with a lint-free cloth.

Make sure no dirt or dust remains on the surface of the lens. It will be enlarged and projected onto a screen.

Replacing the Lamp unit

Before replacing the Lamp unit

Switch off the MAIN POWER and disconnect the power plug from the wall outlet.

Wait for more than 1 hour and make sure the lamp unit and the surroundings are cooled enough. Prepare a Phillips-head screwdriver.

Contact an Authorized Service Center to purchase a replacement lamp unit (ET-LAF100).

When the projector is mounted on the ceiling, do not work directly under the projector or put your face closer to the projector.

NOTE:

Prior to replacing the lamp unit, allow it to cool down to prevent the risk of burns, damage and other hazards.

Do not attempt replacement with an unauthorized lamp unit.

When to replace the lamp unit

The lamp unit is consumable and the brightness decreases by duration of usage. The LAMP indicator will inform you of the replacement timing at 5 000 hours, and at 6 000 hours, the projector will be turned off. Those figures are rough guidance and might be shortened by the usage conditions, characteristics of the lamp unit, environmental conditions, and so on. You can check the duration of usage time using RUNTIME of STATUS in the PROJECTOR SETUP menu.

On screen

LAMP indicator

Indication

REPLACE LAMP

Maintenance

Over 5 000 hours

REPLACE LAMP” is displayed on the

 

upper left of the screen for 10 minutes.

 

 

 

 

 

 

 

REPLACE LAMP” is displayed on the

Illuminates red.

Over 6 000 hours

upper left of the screen, and it will stay until

you respond.

 

 

 

 

To clear the screen, press any button.

 

NOTE:

The guide times, 5 000 and 6 000 hours, are rough estimates based on certain conditions and are not a guaranteed time.

For more information about the lamp unit, such as guaranteed time, see the instructions which is provided with the lamp unit.

ENGLISH - 48

Image 48
Contents PT-FW300U Important Safety Notice Dear Panasonic CustomerImportant Safety Notice Declaration of ConformityTrade Name PanasonicContents Settings MaintenanceContents AppendixPrecautions with regard to safety Precautions with regard to safety Do not set up the projector outdoorsDo not look into the lens while the projector is being used Remove the used batteries from the remote control promptly Do not put your weight on this projectorUse only the specified batteries Do not mix old and new batteriesSecurity Order to get the best picture qualityLiquid crystal panel Optical componentsAccessories Power cordPower cord secure lock Minimum required setting screen Read this firstAbout Your Projector Projector bodyTop and front view Control panelAuto cleaning filter ACF Front leg Adjusters Compartment About Your Projector Back and bottom viewSecurity lock Lamp unit compartment Air exhaust portRemote control Attaching a hand strap Top view Remote control indicatorCLOCK, Clock Phase and Signal Search for Battery compartmentSetting up Screen size and throw distanceCalculation methods Projection size 16 Throw distance LFront leg adjusters and throwing angle Setting upProjection method Mounting on the ceiling and projecting from frontAdjusting the lens shift lever Lens shift and positioningHorizontal shift Vertical shiftSetting up Projector location range When the screen position is fixedWhen the projector position is fixed Connecting example Computers ConnectionsBefore connection to the projector LAN terminalConnecting example AV equipment Connecting with Video IN/S-VIDEOConnecting with DVI-D ConnectionsSwitching the projector on/off Power cordConnecting Direct power on functionPower indicator Switching the projector on/offPower indicator informs you the status of the power Switching on the projector Switching off the projectorSwitch the Main Power on Press the power button Switch off the Main Power on the back of the projectorSelecting the input signal Projecting an imagePositioning the image Remote control operation Setting up the image position automaticallyOperating range Facing to the projectorSwitching the input signal Enlarging the centered areaResetting to the factory default settings Projecting an image in INDEX-WINDOW modeCapturing an image Stopping the projectionUsing an assigned function Switching the signalSide by Side function signal combination table Projecting 2 different source image at a timeUsing the laser pointer Controlling the volume of the speakerDisable the Laser button Laser pointer beam emitterMenu Navigation Main menu and Sub-menuInput Guide OSD DesignClosed Caption Setting Menu NavigationAdjusting with the bar scale items Operating procedureNavigating through the menu Displaying the Main menuPicture menu Color Temperature Daylight ViewDigital Cinema Reality TV-SYSTEMPosition menu Aspect Position menuAspect ratio options 169Frame Lock Closed Caption Setting Screen SettingDisplay Option menu DVI-DAuto Setup Signal SearchWide Mode Sxga ModeOther Functions Display Option menuProjector Setup menu No Signal SHUT-OFFStatus COMPUTER2 SelectInstallation High Altitude ModeAudio Setting Function ButtonFilter Counter Reset Test PatternInitialize ALL Remaining Filter of Status in ProjectorPassword Password ChangeSecurity menu Text DisplayMenu Lock Password Control Device SetupMenu Lock Security menuWireless LAN PT-FW300NTUonly Network menuItems in Network menu Network menu, the following items are availableTEMP, Lamp and Filter Indicators Managing the indicated problemsLamp indicator Temp indicatorCare and Replacement Cleaning the projectorReplacing the Lamp unit Replacing the Auto Cleaning Filter ACF Care and Replacement Replacement procedureWhen to replace the ACF Before replacing the ACFResetting the Remaining Counter Reset in Projector SetupTurn the projector upside down and place it gently On a soft clothTroubleshooting List of compatible signals Technical InformationQuality*2 KHz MHzSerial terminal Technical Information Cable specifications Control commandsComputer connection guidance ProjectorLamp switching Switching input SignalsInput signal Remote terminalCeiling mount bracket safeguards Installing the safety cableDVI-D in terminal Screen size and throw distance for 169 aspect ratio Screen size and throw distance for 43 aspect ratioSW m = SD x SH m = SD x LW m = 0.0339 x SD LT m = 0.0653 x SDSpecifications Video OUTDVI-D AudioDimensions Trademark acknowledgementsUnit mm Index FunctionPicture Mode IndexAvis important concernant la sécurité PT-FW300NTU/PT-FW300UNuméro de série Avis important concernant la sécurité AvertissementAdvertencia Déclaration de conformitéPrécautions de sécurité AvertissementMises EN Garde Précautions de sécuritéPrécautions lors de linstallation Précautions lors du transportPrécautions lors de lutilisation Sécurité Affichage à cristaux liquidesComposants optiques Remplacement de lunité de la lampe Délai de remplacement de lUnité de la lampeAvant de remplacer le lUnité de la lampe Installation du câble de sécurité Protections du support de montage au plafondRetirer et remplacer la lampe