Panasonic PT-FW300U manual Remote terminal, Lamp switching, Switching input Signals, Input signal

Page 55

Technical Information

REMOTE terminal

You can remotely operate the projector from the outside the remote control range by connecting to the REMOTE terminal.

Pin assignments and signal names

	Pin No.	Signal name	Contents
	A	GND	Ground

	B	POWER	POWER ON

	C	INPUT SEL3	Select input signal 3

	D		NC

	E	INPUT SEL1	Select input signal 1

	F	INPUT SEL2	Select input signal 2

	G		Connect internally

	H
	H

	I	ENABLE	Control by external contact

LAMP switching

Pin No.								Settings
B - A					Short					Open
Operation						On				Off

Switching input			signals

Pin No.							Settings
C - A		Open		Open		Open		Short		Short	Open
E - A		Open		Short		Open		Open		Short	Short
F - A		Open		Open		Short		Open		Open	Short
Input signal		COMPUTER1		COMPUTER2		DVI		VIDEO		S-VIDEO	NETWORK

NOTE:

•When pin A and pin I are short-circulated, the buttons on the projector’s control panel, power and INPUT SELECT buttons on the remote control cannot be used. In addition, the RS-232C commands and network functions that correspond to these functions cannot be used either.

•While pin I is “Open”, do not short-circuit pin A, B, C, E and F. The projector would reject all the signals from the remote control.

Appendix

ENGLISH - 55

Image 55

Contents PT-FW300U Dear Panasonic Customer Important Safety NoticePanasonic Important Safety NoticeDeclaration of Conformity Trade NameContents Appendix SettingsMaintenance ContentsPrecautions with regard to safety Do not set up the projector outdoors Precautions with regard to safetyDo not look into the lens while the projector is being used Do not mix old and new batteries Remove the used batteries from the remote control promptlyDo not put your weight on this projector Use only the specified batteriesOptical components SecurityOrder to get the best picture quality Liquid crystal panelPower cord AccessoriesPower cord secure lock Read this first Minimum required setting screenControl panel About Your ProjectorProjector body Top and front viewLamp unit compartment Air exhaust port Auto cleaning filter ACF Front leg Adjusters CompartmentAbout Your Projector Back and bottom view Security lockBattery compartment Remote controlAttaching a hand strap Top view Remote control indicator CLOCK, Clock Phase and Signal Search forProjection size 16 Throw distance L Setting upScreen size and throw distance Calculation methodsMounting on the ceiling and projecting from front Front leg adjusters and throwing angleSetting up Projection methodVertical shift Adjusting the lens shift leverLens shift and positioning Horizontal shiftWhen the screen position is fixed Setting up Projector location rangeWhen the projector position is fixed LAN terminal Connecting example ComputersConnections Before connection to the projectorConnections Connecting example AV equipmentConnecting with Video IN/S-VIDEO Connecting with DVI-DDirect power on function Switching the projector on/offPower cord ConnectingSwitching the projector on/off Power indicatorPower indicator informs you the status of the power Switch off the Main Power on the back of the projector Switching on the projectorSwitching off the projector Switch the Main Power on Press the power buttonProjecting an image Selecting the input signalPositioning the image Facing to the projector Remote control operationSetting up the image position automatically Operating rangeEnlarging the centered area Switching the input signalStopping the projection Resetting to the factory default settingsProjecting an image in INDEX-WINDOW mode Capturing an imageProjecting 2 different source image at a time Using an assigned functionSwitching the signal Side by Side function signal combination tableLaser pointer beam emitter Using the laser pointerControlling the volume of the speaker Disable the Laser buttonOSD Design Menu NavigationMain menu and Sub-menu Input GuideMenu Navigation Closed Caption SettingDisplaying the Main menu Adjusting with the bar scale itemsOperating procedure Navigating through the menuPicture menu TV-SYSTEM Color TemperatureDaylight View Digital Cinema RealityPosition menu 169 AspectPosition menu Aspect ratio optionsFrame Lock DVI-D Closed Caption SettingScreen Setting Display Option menuSxga Mode Auto SetupSignal Search Wide ModeDisplay Option menu Other FunctionsCOMPUTER2 Select Projector Setup menuNo Signal SHUT-OFF StatusFunction Button InstallationHigh Altitude Mode Audio SettingRemaining Filter of Status in Projector Filter Counter ResetTest Pattern Initialize ALLText Display PasswordPassword Change Security menuSecurity menu Menu Lock PasswordControl Device Setup Menu LockNetwork menu, the following items are available Wireless LAN PT-FW300NTUonlyNetwork menu Items in Network menuTemp indicator TEMP, Lamp and Filter IndicatorsManaging the indicated problems Lamp indicatorCleaning the projector Care and ReplacementReplacing the Lamp unit Before replacing the ACF Replacing the Auto Cleaning Filter ACFCare and Replacement Replacement procedure When to replace the ACFOn a soft cloth Resetting the RemainingCounter Reset in Projector Setup Turn the projector upside down and place it gentlyTroubleshooting KHz MHz List of compatible signalsTechnical Information Quality*2Serial terminal Projector Technical Information Cable specificationsControl commands Computer connection guidanceRemote terminal Lamp switchingSwitching input Signals Input signalInstalling the safety cable Ceiling mount bracket safeguardsDVI-D in terminal LW m = 0.0339 x SD LT m = 0.0653 x SD Screen size and throw distance for 169 aspect ratioScreen size and throw distance for 43 aspect ratio SW m = SD x SH m = SD xSpecifications Audio VideoOUT DVI-DTrademark acknowledgements DimensionsUnit mm Function IndexIndex Picture ModePT-FW300NTU/PT-FW300U Avis important concernant la sécuritéNuméro de série Déclaration de conformité Avis important concernant la sécuritéAvertissement AdvertenciaAvertissement Précautions de sécuritéPrécautions de sécurité Mises EN GardePrécautions lors du transport Précautions lors de linstallationPrécautions lors de lutilisation Affichage à cristaux liquides SécuritéComposants optiques Délai de remplacement de lUnité de la lampe Remplacement de lunité de la lampeAvant de remplacer le lUnité de la lampe Protections du support de montage au plafond Installation du câble de sécuritéRetirer et remplacer la lampe