Panasonic PT-FW300U, PT-FW300NTU manual Serial terminal

Page 53

Technical Information

Serial terminal

The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer which is connected to this connecter.

Connection

D-sub 9 pin (male)

Computer

Serial terminal (female)

Pin assignments and signal names

	Pin No.	Signal name	Contents
	A		NC
	B	TXD	Transmitted data
	C	RXD	Received data
	D		NC
	E	GND	Earth
	F		NC
	G	RTS	Connected internally
	H	CTS	Connected internally
	H	CTS
	I		NC

Communication settings

Signal level	RS-232C	Character length	8 bits

Sync. method	Asynchronous	Stop bit	1 bit

Baud rate	9 600 bps	X parameter	None

Parity	None	S parameter	None

Basic format

STX

Command

:

Parameter

ETX

The data streaming from the computer will start

with STX, and proceed to Command,

Start

byte

1 byte

End

Parameter and end with ETX. You can add the

3 bytes

1 byte -

(02h)

(03h)

required parameter.

4 bytes

The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds before sending the command.

If sending multiple commands, check that a response has been received from the projector for one command before sending the next command.

When a command which does not require parameters to be sent, the colon (:) is not required.

If an incorrect command is sent from the personal computer, the ER401 command will be sent from the projector to the personal computer.

Appendix

ENGLISH - 53

Image 53

Contents PT-FW300U Dear Panasonic Customer Important Safety NoticeDeclaration of Conformity Important Safety NoticeTrade Name PanasonicContents Maintenance SettingsContents AppendixPrecautions with regard to safety Do not look into the lens while the projector is being used Precautions with regard to safetyDo not set up the projector outdoors Do not put your weight on this projector Remove the used batteries from the remote control promptlyUse only the specified batteries Do not mix old and new batteriesOrder to get the best picture quality SecurityLiquid crystal panel Optical componentsPower cord secure lock AccessoriesPower cord Read this first Minimum required setting screenProjector body About Your ProjectorTop and front view Control panelAbout Your Projector Back and bottom view Auto cleaning filter ACF Front leg Adjusters CompartmentSecurity lock Lamp unit compartment Air exhaust portAttaching a hand strap Top view Remote control indicator Remote controlCLOCK, Clock Phase and Signal Search for Battery compartmentScreen size and throw distance Setting upCalculation methods Projection size 16 Throw distance LSetting up Front leg adjusters and throwing angleProjection method Mounting on the ceiling and projecting from frontLens shift and positioning Adjusting the lens shift leverHorizontal shift Vertical shiftWhen the projector position is fixed Setting up Projector location rangeWhen the screen position is fixed Connections Connecting example ComputersBefore connection to the projector LAN terminalConnecting with Video IN/S-VIDEO Connecting example AV equipmentConnecting with DVI-D ConnectionsPower cord Switching the projector on/offConnecting Direct power on functionPower indicator informs you the status of the power Power indicatorSwitching the projector on/off Switching off the projector Switching on the projectorSwitch the Main Power on Press the power button Switch off the Main Power on the back of the projectorPositioning the image Selecting the input signalProjecting an image Setting up the image position automatically Remote control operationOperating range Facing to the projectorEnlarging the centered area Switching the input signalProjecting an image in INDEX-WINDOW mode Resetting to the factory default settingsCapturing an image Stopping the projectionSwitching the signal Using an assigned functionSide by Side function signal combination table Projecting 2 different source image at a timeControlling the volume of the speaker Using the laser pointerDisable the Laser button Laser pointer beam emitterMain menu and Sub-menu Menu NavigationInput Guide OSD DesignMenu Navigation Closed Caption SettingOperating procedure Adjusting with the bar scale itemsNavigating through the menu Displaying the Main menuPicture menu Daylight View Color TemperatureDigital Cinema Reality TV-SYSTEMPosition menu Position menu AspectAspect ratio options 169Frame Lock Screen Setting Closed Caption SettingDisplay Option menu DVI-DSignal Search Auto SetupWide Mode Sxga ModeDisplay Option menu Other FunctionsNo Signal SHUT-OFF Projector Setup menuStatus COMPUTER2 SelectHigh Altitude Mode InstallationAudio Setting Function ButtonTest Pattern Filter Counter ResetInitialize ALL Remaining Filter of Status in ProjectorPassword Change PasswordSecurity menu Text DisplayControl Device Setup Menu Lock PasswordMenu Lock Security menuNetwork menu Wireless LAN PT-FW300NTUonlyItems in Network menu Network menu, the following items are availableManaging the indicated problems TEMP, Lamp and Filter IndicatorsLamp indicator Temp indicatorReplacing the Lamp unit Care and ReplacementCleaning the projector Care and Replacement Replacement procedure Replacing the Auto Cleaning Filter ACFWhen to replace the ACF Before replacing the ACFCounter Reset in Projector Setup Resetting the RemainingTurn the projector upside down and place it gently On a soft clothTroubleshooting Technical Information List of compatible signalsQuality*2 KHz MHzSerial terminal Control commands Technical Information Cable specificationsComputer connection guidance ProjectorSwitching input Signals Lamp switchingInput signal Remote terminalDVI-D in terminal Ceiling mount bracket safeguardsInstalling the safety cable Screen size and throw distance for 43 aspect ratio Screen size and throw distance for 169 aspect ratioSW m = SD x SH m = SD x LW m = 0.0339 x SD LT m = 0.0653 x SDSpecifications OUT VideoDVI-D AudioUnit mm DimensionsTrademark acknowledgements Function IndexIndex Picture ModeNuméro de série Avis important concernant la sécuritéPT-FW300NTU/PT-FW300U Avertissement Avis important concernant la sécuritéAdvertencia Déclaration de conformitéAvertissement Précautions de sécuritéPrécautions de sécurité Mises EN GardePrécautions lors de lutilisation Précautions lors de linstallationPrécautions lors du transport Composants optiques SécuritéAffichage à cristaux liquides Avant de remplacer le lUnité de la lampe Remplacement de lunité de la lampeDélai de remplacement de lUnité de la lampe Retirer et remplacer la lampe Installation du câble de sécuritéProtections du support de montage au plafond