Zebra Technologies SL5000r/T5000r manual Command Prefix, Label Prefix, Delimiter, LP+ Text Mode

Page 12

Chapter 1 PPI/ZGL SETUP Menu

Command Prefix

This item allows you to select the prefix for the control instructions command.

The range is 1-255, and the default is 126.

Label Prefix

This item allows you to select the prefix for the format instructions command.

The range is 1-255, and the default is 94.

Delimiter

This item allows you to select the delimiter used to separate the parameter of a command.

The range is 1-255, and the default is 44.

LP+ Text Mode

PPI supports text printing using the LP+ emulation.

•Absorb (default). Use this setting for ZPL compatibility. This setting absorbs non-PPI data.

•Auto Pass-thru. Use this setting for text printing. Non-PPI data is passed to the LP+ emulation.

•ZGL Quiet. All data and PPI commands are passed to the LP+ emulation.

Preparser Command

The incoming data will be checked for the string “HS” or “JA” prior to entering the ZGL emulation parser based on the HS Command or the JA Command. Once the string is detected, the command will take effect immediately.

The default is HS Command.

Preparser Port

•Disable (default). Disables the Preparser Command feature.

•Parallel. Select Parallel if the data is coming to the printer through the parallel port.

•Serial. Select Serial if the data is coming to the printer through the serial port.

12

Image 12

Contents Printer Protocol Interpreter PPI ZGL Page Page Trademark Acknowledgments Table of Contents Table of Contents Command Enhancements And Differences ZGL-DBCS Introduction About This ManualPPI/ZGL Setup Menu PPI/ZGL SetupPPI/ZGL Setup Submenus ZPL CompatibleCommand Prefix LP+ Text ModePreparser Command Label PrefixMC Label Fmt PQ Label FmtLabel Buf Size Host Form LengthResolution Mode Vertical AdjustLeft Position Top PositionFB Width Adjust Is Label FormatCharacter Group And Character Sets ZGLFully Supported Commands Bx BarcodesBy Barcode Defaults CF Change Alphanumeric Default Font~CC / CC Change Caret ~CD / CD Change Delimiter~EF / EF Erase Format ~EG / EG Erase Downloaded ImagesFA Field Allocate FC Field ClockGS Graphic Symbol FT Field Type SetFW Field Orientation FX Comment~JA Cancel All HY Upload GraphicIL Image Load IM Image MoveMM Print Mode MU Mode UnitsLL Label Length LR Label ReverseTA Tear Off Adjust ~NT Set Currently Connected Printer TransparentPM Print Mirror Image of Label PW Print WidthXF Recall Format XG Recall GraphicXZ Label End @ Select Font by Name Ax Select Alphanumeric Font$x Barcodes $B Upcship CI Select International Set $D FIMMS DOS CP710 CP 858 Euro CW Font Identifier ~DB Download Bitmap Font~DG Download Graphics ~DY Download GraphicFB Field Block FV Field Variable Data$E Switch Emulation ~JD / JE Disable/Enable DiagnosticsHR Calibrate Rfid Transponder Position ~HS Host Status ReturnJE Disable Diagnostics ~JP Pause & CancelJU Configuration Update JV Configuration UpdateMC Mp Clear MD Media DarknessMN Media tracking PF Slew Dot RowsRM Enable Rfid Motion RS Rfid Setup~PP / PP Programmable Pause ~PR / PP Print RateRZ Set Rfid Tag Password ~WC Print ConfigurationAutoexec Bootup File ~SD Set DarknessZGL Menu Conversions Appendix a Pwr Up Auto-Cal Disable*, Enable Validator Menu Opt Format Convert None*, 150-300 PPI/ZGL Setup Menu Default Gateway opt -Sets Gateway Ethernet Address Menu, opt ZGL-DBCS OverviewSelect Alphanumeric Font Command ZGL-DBCS SeriesSelect International Set Command OritFont Identifier Command Printronix Customer Support Center Printronix Supplies DepartmentCorporate Offices Page 174779-001