Zebra Technologies SL5000r/T5000r manual MC Mp Clear, MD Media Darkness, MN Media tracking

Page 34

Chapter 3

When LP+ Text Mode is set to “Auto Pass-thru,” non-PPI data is automatically detected and passed through to the LP+ emulation (PPI data is processed normally). If the hex commands 0x02 or 0x03 are received, they are treated as binary data and passed through to the LP+ emulation; they are not treated as the equivalent ^XA and ^XZ commands. System-generated line terminators within commands are also passed through as binary data to the LP+ emulation and not absorbed, as they are in the “Absorb” mode.

If LP+ Text Mode is set to “ZGL Quiet,” all data (including all PPI commands except ~L0, ~L1, and ~L2) are passed through to the LP+ emulation. When an ~Lx command is received, the corresponding front panel setting is updated to reflect the current LP+ Text Mode value.

Text printing is useful in debugging label definitions, as it allows the incoming data to be printed without entering hex dump mode. Simply placing ~L2 before the label definition (to enter Quiet mode) and ~L0 or ~L1 after it (to return to PPI command processing) causes the label definition commands to be printed rather than executed. Text generated via the base emulation is not part of overlay data for any repetitive job.

^MC - Mp Clear

This command controls clearing of the label bitmap after printing. PPI may not keep the previous label as a bitmap, but as text.

^MD - Media Darkness

Identical darkness values may not produce the same darkness on your printer as ZPL.

^MN - Media tracking

This command selects the type of media the printer is using: continuous, transmissive, or reflective.

^PF - Slew Dot Rows

With PPI, a slew speed increase may not occur since PSA slew definition and use may be different than ZPL.

~PH / ^PH - Slew to Home

The PPI ONLINE light is illuminated when the printer is online.

^PO - Print Orientation

The following orientation parameter values are allowed:

N: No rotation (Normal)

R:Rotate 90 degrees (Landscape) I : Rotate 180 degrees (Inverted)

B:Rotate 270 degrees (Inverted Landscape)

34

Image 34
Contents Printer Protocol Interpreter PPI ZGL Page Page Trademark Acknowledgments Table of Contents Table of Contents Command Enhancements And Differences ZGL-DBCS Introduction About This ManualPPI/ZGL Setup Menu PPI/ZGL SetupPPI/ZGL Setup Submenus ZPL CompatiblePreparser Command Command PrefixLP+ Text Mode Label PrefixLabel Buf Size MC Label FmtPQ Label Fmt Host Form LengthLeft Position Resolution ModeVertical Adjust Top PositionFB Width Adjust Is Label FormatCharacter Group And Character Sets ZGLFully Supported Commands Bx Barcodes~CC / CC Change Caret By Barcode DefaultsCF Change Alphanumeric Default Font ~CD / CD Change DelimiterFA Field Allocate ~EF / EF Erase Format~EG / EG Erase Downloaded Images FC Field ClockFW Field Orientation GS Graphic SymbolFT Field Type Set FX CommentIL Image Load ~JA Cancel AllHY Upload Graphic IM Image MoveLL Label Length MM Print ModeMU Mode Units LR Label ReversePM Print Mirror Image of Label TA Tear Off Adjust~NT Set Currently Connected Printer Transparent PW Print WidthXG Recall Graphic XF Recall FormatXZ Label End Ax Select Alphanumeric Font @ Select Font by Name$x Barcodes $B Upcship CI Select International Set $D FIMMS DOS CP710 CP 858 Euro CW Font Identifier ~DB Download Bitmap FontFB Field Block ~DG Download Graphics~DY Download Graphic FV Field Variable DataHR Calibrate Rfid Transponder Position $E Switch Emulation~JD / JE Disable/Enable Diagnostics ~HS Host Status ReturnJU Configuration Update JE Disable Diagnostics~JP Pause & Cancel JV Configuration UpdateMN Media tracking MC Mp ClearMD Media Darkness PF Slew Dot Rows~PP / PP Programmable Pause RM Enable Rfid MotionRS Rfid Setup ~PR / PP Print RateAutoexec Bootup File RZ Set Rfid Tag Password~WC Print Configuration ~SD Set DarknessZGL Menu Conversions Appendix a Pwr Up Auto-Cal Disable*, Enable Validator Menu Opt Format Convert None*, 150-300 PPI/ZGL Setup Menu Default Gateway opt -Sets Gateway Ethernet Address Menu, opt ZGL-DBCS OverviewSelect Alphanumeric Font Command ZGL-DBCS SeriesSelect International Set Command OritFont Identifier Command Printronix Customer Support Center Printronix Supplies DepartmentCorporate Offices Page 174779-001