Zebra Technologies SL5000r/T5000r manual JE Disable Diagnostics, ~JP Pause & Cancel

Page 33

^JE - Disable Diagnostics

This command disables Hex Dump mode.

~JP - Pause & Cancel

The PPI ONLINE light is illuminated when the printer is online.

^JU - Configuration Update

This command controls whether the printer reprints a label after a fault condition clears.

^JU op, num

op = Configuration update operation to perform. F: Load factory configuration

R:Load saved configuration number num

S:Save current configuration as power-up configuration number num

num = Configuration number to load, used only when op = R or S

^JV - Configuration Update

This command saves/loads the configuration ^JVa[,m]

a = F: Load factory emulation

S:Save configuration and as power-up configuration

R:Load saved configuration

m = 1 ... 8 (config number)

^JZ - Reprint After Error

The current setting is reflected in the corresponding front panel value. The conditions which generate a fault are determined by, and may be unique to, PSA.

~Lx - Base Emulation Support

PPI supports text printing using the LP+ emulation.

In addition to the three front panel LP+ Text Mode selections, there are three PPI commands which allow you to select the LP+ Text Mode through the data stream:

~L0 - LP+ Text Mode = Absorb (ZPL compatibility) ~L1 - LP+ Text Mode = Auto Pass-thru

~L2 - LP+ Text Mode = ZGL Quiet

With LP+ Text Mode set to “Absorb,” all non-PPI data is absorbed including any system-generated line terminators.

33

Image 33

Contents Printer Protocol Interpreter PPI ZGL Page Page Trademark Acknowledgments Table of Contents Table of Contents Command Enhancements And Differences ZGL-DBCS About This Manual IntroductionPPI/ZGL Setup PPI/ZGL Setup MenuZPL Compatible PPI/ZGL Setup SubmenusLP+ Text Mode Command PrefixPreparser Command Label PrefixPQ Label Fmt MC Label FmtLabel Buf Size Host Form LengthVertical Adjust Resolution ModeLeft Position Top PositionIs Label Format FB Width AdjustZGL Character Group And Character SetsBx Barcodes Fully Supported CommandsCF Change Alphanumeric Default Font By Barcode Defaults~CC / CC Change Caret ~CD / CD Change Delimiter~EG / EG Erase Downloaded Images ~EF / EF Erase FormatFA Field Allocate FC Field ClockFT Field Type Set GS Graphic SymbolFW Field Orientation FX CommentHY Upload Graphic ~JA Cancel AllIL Image Load IM Image MoveMU Mode Units MM Print ModeLL Label Length LR Label Reverse~NT Set Currently Connected Printer Transparent TA Tear Off AdjustPM Print Mirror Image of Label PW Print WidthXF Recall Format XG Recall GraphicXZ Label End @ Select Font by Name Ax Select Alphanumeric Font$x Barcodes $B Upcship $D FIM CI Select International SetMS DOS CP710 CP 858 Euro ~DB Download Bitmap Font CW Font Identifier~DY Download Graphic ~DG Download GraphicsFB Field Block FV Field Variable Data~JD / JE Disable/Enable Diagnostics $E Switch EmulationHR Calibrate Rfid Transponder Position ~HS Host Status Return~JP Pause & Cancel JE Disable DiagnosticsJU Configuration Update JV Configuration UpdateMD Media Darkness MC Mp ClearMN Media tracking PF Slew Dot RowsRS Rfid Setup RM Enable Rfid Motion~PP / PP Programmable Pause ~PR / PP Print Rate~WC Print Configuration RZ Set Rfid Tag PasswordAutoexec Bootup File ~SD Set DarknessZGL Menu Conversions Appendix a Pwr Up Auto-Cal Disable*, Enable Validator Menu Opt Format Convert None*, 150-300 PPI/ZGL Setup Menu Default Gateway opt -Sets Gateway Ethernet Address Menu, opt Overview ZGL-DBCSZGL-DBCS Series Select Alphanumeric Font CommandOrit Select International Set CommandFont Identifier Command Printronix Supplies Department Printronix Customer Support CenterCorporate Offices Page 174779-001