Nortel Networks P0605618, 555-7101-217 manual Conventions for warnings

Page 28

Preparing for installation

Standard 1.0

Conventions for warnings

You may encounter the following types of warnings in this guide. Do not ignore them.

DANGER

Risk of electric shock

Warns you of an immediate electrical hazard which, if not avoided, will result in shock, serious injury, or death.

WARNING

Risk of personal injury

Warns you of a situation in which you can be injured if instructions are not followed exactly as stated.

CAUTION

Risk of equipment damage

Alerts you to situations where data can be lost or damaged, equipment can be damaged, actions can result in service interruption, and productive time can be lost.

ATTENTION

Provides information that is essential to the completion of a task.

28

CallPilot

Image 28
Contents CallPilot P0605618 CallPilot Page Publication history Publication history Contents Devices Installing the server and connecting the peripheralIndex 1001rp server description A p t e rServer features Server dimensions and weightIntroduction 49.5 cm 19.5Front panel features front view without the front bezel Alarm boardRear panel diagram Overhead view of empty server showing PCI and ISA connectors Slot definition and slot numbering Slot assignments1001rp slot assignments Single Board Computer Slot Reserved for COM1 COM2 I/O bracket SlotElan Network card Slot Clan Network card Slot 12bBRD20 IRQ mapping table IRQ Network connectivity Sample network setup Meridian Customer LAN optionalSample network setup Succession CSE Telephony LAN/Customer LAN 10/100BaseT or 100BaseTSwitch connectivity CallPilot Elan and Clan network setupRemote access connectivity Network requirementsSupported peripheral devices Modem Kbps external modem NTRH9078 providesSince the modem is an external device, it requires its own Also supported, but has been replaced by the 56 KbpsPreparing for installation Installation overview Installation checklistMay 2003Preparing for installation Conventions for warnings Unpacking the 1001rp server Follow this procedure to unpack the server and peripheralsTo unpack the equipment What’s next? Removing the front bezel and server cover About the front bezel doorsTo remove the front bezel High current inside the chassis can cause severe injury To remove the server coverContinue with Inspecting the server interior on To replace the front bezel after installation is complete Inspecting the server interior To inspect the server interiorPreparing for installationStandard Power supply installation Safety information Safety precautionsEquipment handling guidelines Section a Installing the power supply modules AC or DC About the power supply module Installing the second power supply module AC or DCAC versus DC systems Power supply modules To install the power supply module Do one of the followingSection B Setting up DC power source for a 1001rp DC server DC wire gauge tables Metric wire conversion Following diagram shows typical rack power cabling DC rack cabling48VDC power distribution rationale About the Power Distribution Unit Multiple PDUsPDU terminal blocks and wiring diagram DC power inputBringing power and ground into the PDU To bring DC power and ground into the PDUMay Power supply installation Installing the server and connecting the peripheral devices Installing the server To install the serverPreparing the modem Required equipmentModem DIP switches DIPTo set the modem DIP switches OFF The modem sends a CD signal when it OFF Loads Y or Y1 configuration fromAT command set recognition OFF Disables command recognition dumbConnecting peripherals to the server Rear panel connectionsTo connect the mouse, keyboard, and monitor to the server To connect the modem to the serverContinue with Connecting the server to the Elan on Media Access Control address Connecting the server to the ElanTo connect the server to the Elan Feature key adapter dongle. See Connecting the server to the Clan optional To connect the server to the ClanWhat’s next? Installing the Nortel Networks software feature key adapter To install the software feature key adapter For installation, you require a Phillips No screwdriverContinue with Connecting the server to power on RequirementsConnecting the server to power Before you beginCallPilot server To connect the 1001rp AC server to power To connect the 1001rp DC server to power Connect the DC power cable to the server, as shown belowTo start the server Binder Installing the server and connecting the peripheral devices Index Clan Elan May Index Index Page Product release Document release Standard Date May